KENT 908 7113 020 Скачать руководство пользователя

Страница: 6 / 58

GENERAL INFORMATION

ENGLISH

SERVICE MANUAL

909 6577 000(4)2009-11

Razor SV17 - Razor E17

WARNING!

[Razor SV17 - Razor E17]

Do not leave the machine unattended without being sure that it cannot move independently.

–

Always protect the machine against the sun, rain and bad weather, both under operation and inactivity

–

condition. Store the machine indoors, in a dry place: This machine must be used in dry conditions, it must

not be used or kept outdoors in wet conditions.

Before using the machine, close all doors and/or covers.

–

Do not allow to be used as a toy. Close attention is necessary when used near children.

–

Use only as shown in this Manual. Use only KENT recommended accessories.

–

Take all necessary precautions to prevent hair, jewelry and loose clothes from being caught by the machine

–

moving parts.

Do not leave the machine unattended without being sure that it cannot move independently.

–

While using this machine, take care not to cause damage to people or objects.

–

Do not bump into shelves or scaffoldings, especially where there is a risk of falling objects.

–

Do not put any can containing fluids on the machine.

–

The machine working temperature must be between

–

+32°F and +104°F (0°C and +40°C).

The machine storage temperature must be between

–

+32°F and +104°F (0°C and +40°C).

The humidity must be between 30% and 95%.

–

When using floor cleaning detergents, follow the instructions on the labels of the detergent bottles.

–

To handle floor cleaning detergents, wear suitable gloves and protections.

–

Do not use the machine as a means of transport.

–

Do not use the machine on incline.

–

Do not allow the brushes to operate while the machine is stationary to avoid damaging the floor.

–

In case of fire, use a powder fire extinguisher, not a water one.

–

Do not tamper with the machine safety guards and follow the ordinary maintenance instructions

–

scrupulously.

Do not allow any object to enter into the openings. Do not use the machine if the openings are clogged.

–

Always keep the openings free from dust, hairs and any other foreign material which could reduce the air

flow.

Do not remove or modify the plates affixed to the machine.

–

This machine cannot be used on roads or public streets.

–

Pay attention during machine transportation when temperature is below freezing point. The water in the

–

recovery tank or in the hoses could freeze and seriously damage the machine.

Use the brushes and pads supplied with the machine and those specified in the Instructions for Use

–

Manual. Using other brushes or pads could reduce safety.

In case of machine malfunctions, ensure that these are not due to lack of maintenance. Otherwise, request

–

assistance from the authorized personnel or from an authorized Service Center.

If parts must be replaced, require ORIGINAL spare parts from an Otherwise Dealer or Retailer.

–

To ensure machine proper and safe operation, the scheduled maintenance shown in the relevant chapter of

–

this Manual, must be performed by the authorized personnel or by an authorized Service Center.

Carefully read all the instructions before performing any maintenance/repair procedure.

–

Do not wash the machine with direct or pressurized water jets, or with corrosive substances.

–

The machine must be disposed of properly, because of the presence of toxic-harmful materials (batteries,

–

etc.), which are subject to standards that require disposal in special centers (see Scrapping chapter).

WARNING!

[Razor SV17]

Before using the battery charger, ensure that frequency and voltage values, indicated on the machine serial

–

number plate, match the electrical mains voltage.

Do not pull or carry the machine by the battery charger cable and never use the battery charger cable as

–

a handle. Do not close a door on the battery charger cable, or pull the battery charger cable around sharp

edges or corners. Do not run the machine on the battery charger cable. Keep the battery charger cable

away from heated surfaces.

Do not charge the batteries if the battery charger cable or the plug are damaged. If the machine is not

–

working as it should, has been damaged, left outdoors or dropped into water, return it to the Service Center.

To reduce the risk of fire, electric shock, or injury, do not leave the machine unattended when it is plugged

–

in. Before performing any maintenance procedure, disconnect the battery charger cable from the electrical

mains.

Do not smoke while charging the batteries.

–

Содержание 908 7113 020



























































Результаты поиска

Содержание 908 7113 020

Отзывы:

Похожие инструкции для 908 7113 020

Бренды по названию

Популярные бренды

KENT 908 7113 020, Руководство по обслуживанию

Результаты поиска

Содержание 908 7113 020

Отзывы:

Похожие инструкции для 908 7113 020

Бренды по названию

Популярные бренды