KENT 908 7113 020 Скачать руководство пользователя | Manualshive

Страница: 27 / 58

background image

RECOVERY WATER SYSTEM

SERVICE MANUAL

ENGLISH

Razor SV17 - Razor E17

909 6577 000(4)2009-11

25

RECOVERY WATER SYSTEM
TANK AND VACUUM GRID WITH FLOAT CLEANING [Razor SV17 - Razor E17]

Drive the machine to the appointed disposal area.

1.

Check that the switches (5 and 6) are turned to “0”.

2.

If necessary, empty the tank (43) by means of the hose (22).

3.

Lift the cover (41), then wash with clean water the cover, the tank (43) and the vacuum grid (46).

4.

Drain the water in the tank through the hose (22).

If necessary, release the fasteners (A) and open the grid (B), recover the float (C), clean all the components and then reinstall

5.

them.

Check the recovery water tank cover gasket (D) for integrity.

6.

NOTE

The gasket (D) creates vacuum in the tank that is necessary for vacuuming the recovery water.

If necessary replace the gasket (D) after removing it from its housing (E).

When assembling the new gasket, install its joint (F) in the central area, as shown in the figure.

Check the gasket (G) bearing surface (D) for integrity and sealing capabilities.

7.

Check the compensation hole (H) for clogging.

8.

NOTE

The hole (H) compensates the air in the cover interspaces, thus allowing the creation of vacuum in the recovery

water tank.

Close the cover (41).

9.

S301372

«
...
25
26
27
28
29
...
»

Содержание 908 7113 020



























































Отзывы:

Нет отзывов

Похожие инструкции для 908 7113 020

Бренд: ebm-papst Страницы: 11

Sno-Thro 932001

Бренд: Ariens Страницы: 12

Бренд: EarthWise Страницы: 8

Бренд: Siemens Страницы: 8

Бренд: Scarab Страницы: 2

Бренд: Trident Страницы: 20

Бренд: Toro Страницы: 28

Бренд: VentAHood Страницы: 3

Бренд: SereneLife Страницы: 24

BACKPACKER II UT08570

Бренд: Homelite Страницы: 18

Бренд: Talon Tools Страницы: 4

Бренд: Kobalt Страницы: 44

Бренд: Geen Works Страницы: 18

Бренд: Arcoaire Страницы: 6

Бренд: Vortice Страницы: 108

Бренд: Troy-Bilt Страницы: 24

Бренд: Zenoah Страницы: 32

Бренд: Kärcher Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды