KENT 908 7113 020 Скачать руководство пользователя

Страница: 7 / 58

GENERAL INFORMATION

SERVICE MANUAL

ENGLISH

Razor SV17 - Razor E17

909 6577 000(4)2009-11

WARNING!

[Micromatic™ M17E]

The machine power supply cable is grounded and the relevant plug is grounded too. In case of machine

–

malfunction or breakdown, grounding connection reduces the risk of electric shock.

The power supply cable plug must be connected to an appropriate outlet, which is grounded according to

–

law in force.

Improper connection can cause electric shock. Consult a qualified technician to make sure that the outlet is

–

properly grounded.

Do not tamper with the power supply cable plug. If the power supply cable plug cannot be connected to the

–

outlet, have new grounded outlet installed by a qualified technician, according to the law in force.

Before connecting the power supply cable to the electrical mains, check that frequency and voltage, shown

–

on the machine serial number plate (7), match the electrical mains voltage.

Do not unplug the machine by pulling the supply cable. To unplug, grasp the plug, not the cable.

–

Do not handle the plug or the machine with wet hands.

–

Turn off all controls before unplugging.

–

Regularly check the power supply cable for damages, cracks, cuts and wear. If necessary, replace it.

–

If the power supply cable is damaged, it must be replaced by an authorized Service Center.

–

To avoid any risk, if the power supply cable is damaged, contact an authorized KENT Service Center or a

–

qualified technician.

Do not pull or carry the machine by the power supply cable and never use the power supply cable as a

–

handle. Do not close a door on the power supply cable, or pull the power supply cable around sharp edges

or corners. Do not run the machine on the power supply cable.

The brushes must not come into contact with the power supply cable.

–

Keep the power supply cable away from heated surfaces.

–

To reduce the risk of fire, electric shock, or injury, do not leave the machine unattended when it is plugged

–

in. Disconnect the machine from the electrical mains when not in use and before performing maintenance

procedures.

If the machine

–

does not work properly

•

is damaged

•

has water or foam leaks

•

has been left outdoors exposed to bad weather conditions

•

is wet or has been dropped into water

•

turn it off immediately and contact the authorized KENT Service Center or a qualified technician.

Содержание 908 7113 020



























































Результаты поиска

Содержание 908 7113 020

Отзывы:

Похожие инструкции для 908 7113 020

Бренды по названию

Популярные бренды

KENT 908 7113 020, Руководство по обслуживанию

Результаты поиска

Содержание 908 7113 020

Отзывы:

Похожие инструкции для 908 7113 020

Бренды по названию

Популярные бренды