manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации

Keithley 7001 - многофункциональный коммутационный/измерительный главный фреймворк. Руководство пользователя доступно для быстрого доступа и скачивания на нашем сайте. Скачивайте бесплатно Руководство по быстрому доступу для Keithley 7001 с нашего веб-сайта manualshive.com.

Поделиться
Скачать
background image

 

7

Maintenance

 

7.1

Introduction ......................................................................................................................................................  7-1

7.2

Service options................................................................................................................................................... 7-1

7.3

Handling and cleaning ..................................................................................................................................... 7-2

7.3.1

Backplane board ........................................................................................................................................ 7-2

7.3.2

Static-sensitive devices ............................................................................................................................. 7-2

7.4

Routine maintenance ........................................................................................................................................ 7-3

7.4.1

Line voltage selection ..............................................................................................................................  7-3

7.4.2

Changing the fuse ....................................................................................................................................  7-3

7.4.3

Changing the battery ................................................................................................................................ 7-3

7.4.4

Changing firmware..................................................................................................................................  7-4

7.5

Disassembly of the instrument........................................................................................................................ 7-4

7.5.1

Removal of the case..................................................................................................................................  7-4

7.5.2

Removal of individual boards................................................................................................................  7-5

7.5.3

Replacement of the case ........................................................................................................................... 7-7

7.6

Diagnostics ......................................................................................................................................................... 7-8

7.6.1

Preparations for running the diagnostics .............................................................................................  7-8

7.6.2

Initial power-up test ................................................................................................................................  7-8

7.6.3

Non-volatile memory test ........................................................................................................................ 7-8

7.6.4

Built-in-tests ..............................................................................................................................................  7-9

7.6.5

Display test 

 

 

 keys................................................................................................................................  7-10

7.6.6

Display test 

 

 

 patterns .........................................................................................................................  7-10

7.6.7

Display test Ñ char set ........................................................................................................................... 7-11

7.7

Test description and notes ............................................................................................................................. 7-11

7.7.1

Initial power-up test ..............................................................................................................................  7-11

7.7.2

Non-volatile memory tests....................................................................................................................  7-12

7.7.3

Built-in-tests ............................................................................................................................................. 7-12

7.8

Troubleshooting .............................................................................................................................................. 7-14

7.8.1

Digital board ...........................................................................................................................................  7-14

7.8.2

Display board..........................................................................................................................................  7-15

7.8.3

Power supply ........................................................................................................................................... 7-15

7.8.4

Micro DIN board ....................................................................................................................................  7-16

7.8.5

Backplane board .....................................................................................................................................  7-16

7.8.6

BNC board................................................................................................................................................ 7-16

 

8

Replaceable Parts

 

8.1

Introduction ......................................................................................................................................................  8-1

8.2

Electrical components list ................................................................................................................................ 8-1

8.3

Mechanical parts ............................................................................................................................................... 8-1

8.4

Ordering information ....................................................................................................................................... 8-1

8.5

How to obtain factory service ......................................................................................................................... 8-1

8.6

Document list..................................................................................................................................................... 8-2

 

Appendices

 

A

Interface Function Codes ............................................................................................................................... A-1

B

ASCII Character Codes and IEEE-488 Multiline Interface Command Messages ................................... B-1

C

Controller Programs .......................................................................................................................................  C-1

D

IEEE-488 Bus Overview.................................................................................................................................. D-1

E

IEEE-488 Conformance Information ............................................................................................................. E-1

F

SCPI Conformance Information..................................................................................................................... F-1

 

v

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

AbleNet HouseMate Quick Start Manual preview
HouseMate
Бренд: AbleNet Страницы: 2
Jabra LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES How To Connect preview
LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES
Бренд: Jabra Страницы: 4
Gefen EXT-DVI-441DL User Manual preview
EXT-DVI-441DL
Бренд: Gefen Страницы: 31
ORiNG IGS-1082GP Quick Installation Manual preview
IGS-1082GP
Бренд: ORiNG Страницы: 2
Theben TIMEGUARD WF10COM Installation & Operating Instructions Manual preview
TIMEGUARD WF10COM
Бренд: Theben Страницы: 35
Lindy 32 277 Installation And Use Manual preview
32 277
Бренд: Lindy Страницы: 38
CYP OR-HD88HC Operation Manual preview
OR-HD88HC
Бренд: CYP Страницы: 20
TP-Link LiteWave LS105G Installation Manual preview
LiteWave LS105G
Бренд: TP-Link Страницы: 3
PTN MUH66TP-N User Manual preview
MUH66TP-N
Бренд: PTN Страницы: 44
Heyer AGS 80 D Instructions For Use Manual preview
AGS 80 D
Бренд: Heyer Страницы: 29
NETGEAR ProSafe GSM5212P (German) Installationsanleitung preview
ProSafe GSM5212P
Бренд: NETGEAR Страницы: 2
Accton Technology CheetaHub Power-3004E Quick Installation Manual preview
CheetaHub Power-3004E
Бренд: Accton Technology Страницы: 11
odot ODOT-MS105T User Manual preview
ODOT-MS105T
Бренд: odot Страницы: 15
ATEN Altusen KN9008 User Manual preview
Altusen KN9008
Бренд: ATEN Страницы: 178
socomec SIRCO MOT PV UL Instruction Manual preview
SIRCO MOT PV UL
Бренд: socomec Страницы: 20
Alloy GSS-8T2SFPV2 User Manual preview
GSS-8T2SFPV2
Бренд: Alloy Страницы: 64
3Com LANPLEX 2500 EXTENDEDPLEX 2500 EXTENDED User Manual preview
LANPLEX 2500 EXTENDEDPLEX 2500 EXTENDED
Бренд: 3Com Страницы: 186
i3 International Cortex S243 User Manual preview
Cortex S243
Бренд: i3 International Страницы: 204

Бренды по названию

Популярные бренды

Загрузить еще бренды