manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации, Страница: 161 / 353

Поделиться
Скачать
Keithley 7001 Скачать руководство пользователя страница 161

 

IEEE-488 Reference

 

5-42

 

5.10.3

 

*ESE? 

 

 

 event status enable query

 

 

 

To read the contents of the Standard Event Status Enable Register. 

 

*ESE?

 

This command is used to acquire the value (in decimal) of the Standard Event Status Enable
Register. The binary equivalent of the decimal value determines which bits in the register are
set. When the *ESE? query command is sent, the decimal value is placed in the Output Queue.
When the Model 7001 is addressed to talk, the value is sent from the Output Queue to the com-
puter. 

For example, for an acquired decimal value of 48, the binary equivalent is 00110000. For this
binary value, bits B4 and B5 of the Standard Event Status Enable Register are set. For informa-
tion on the Standard Event Status Enable Register, refer to paragraph 5.6.

The *ESE? query command does not clear the Standard Event Status Enable Register. 

10

OUTPUT 707; “*ESE?”

! Send query command

20

ENTER 707; A$

! Address 7001 to talk

30

PRINT A$

! Display value of register contents

40

END

Purpose

Format

Description

Programming

example

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов