manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации, Страница: 197 / 353

Поделиться
Скачать
Keithley 7001 Скачать руководство пользователя страница 197

 

IEEE-488 Reference

 

5-78

 

5.13.2

 

:OPEN <list>|ALL

 

[:ROUTe]:OPEN  <list>|ALL

Open specified (or all) channels

 

<list> = (@ chanlist)

Open listed channels

ALL

Open all channels

where; chanlist is the specified list of channels (channel list) to be opened.

:open (@ 

chanlist)

:open all

Power-up

All channels open

*RST

No effect

:SYSTem:PRESet

No effect

:OPEN?  <list>

Query state of specified channels.

Short-form formats:

:open? (@ chanlist)

Response message:

1 = specified channel(s) open.
0 = specified channel(s) not open.

The :OPEN command is used to open one or more channels. The <list> parameter is used to
define a channel list (chanlist) the specifies which channels to open. The ALL parameter is used
to simply open all channels. 

The following examples demonstrate various forms for expressing channel entries for a chanlist.

 

Chanlist

 

1!2!4

Single channel (Slot 1, Row 2, Column 4).

2!36

Single channel (Slot 2, Channel 36).

1!6, 1!18, 2!3!6

Multiple channels separated by commas.

1!2:1!10

Range of channels (2 through 10).

1!2:1!10, 2!3!6

Range entry and single entry separated by commas.

1!30:1!40, 2!1:2!10

Range of multiplex channels (last 10 channels on card 1,
first 10 channels on card 2).

1!4!1:1!4!10, 2!1!1:2!1!10

Range of matrix channels (10 columns of row 4 on card 1,
10 columns of row 1 on card 2).

M36

Channel pattern stored at memory location M36.

The :OPEN?  <list> query command is used to determine the state (open or not open) of each
specified channel. After sending this command and addressing the Model 7001 to talk, the val-

Parameters

Short-form

formats

Defaults

Query

command

Description

 

[:ROUTe] subsystem

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов