manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации

Keithley 7001 - многофункциональный коммутационный/измерительный главный фреймворк. Руководство пользователя доступно для быстрого доступа и скачивания на нашем сайте. Скачивайте бесплатно Руководство по быстрому доступу для Keithley 7001 с нашего веб-сайта manualshive.com.

Поделиться
Скачать
background image

Front Panel Operation

4-24

4.6.1

SAVESETUP

The SAVESETUP menu is used for the following oper-
ations: 

•

Save the current setup conditions in memory for
future recall. Up to 10 setups can be saved in mem-
ory.

•

Restore the instrument to setup conditions stored
in memory.

•

Setup the power-on (PWRON) configuration. The
instrument can be set to power-on to the factory
default setup conditions, or power-on to the setup
conditions stored at a specified memory location.

•

Reset the instrument to the original power-on set-
up conditions (see Table 4-3).

Perform the following steps to display the SAVESET-
UP menu: 

1. Display the MAIN MENU (see paragraph 4.6, Gen-

eral rule #1).

2. Use the cursor keys (

 and 

) to place the cursor

on SAVESETUP, and press ENTER to access the
following menu: 

SETUP MENU  

SAVE

RESTORE

PWRON

RESET

SAVE

 

 

Use this menu item to save the current setup

conditions in memory at a specified memory location.
To select SAVE, place the cursor on SAVE and press
ENTER. The following typical message will be dis-
played: 

SAVE SETUP #0 (0-9)

1. To save the current setup at the displayed memory

location, press ENTER. The instrument will return
to the SETUP MENU.

2. To save the current setup to a different memory lo-

cation, key in a value (0 to 9) and press ENTER. The
instrument will return to the SETUP MENU. 

RESTORE 

 

Use this menu item to return the instru-

ment to the setup conditions that are stored in memory
at a specified memory location. To select RESTORE,
place the cursor on RESTORE and press ENTER. The
following typical message will be displayed: 

RESTORE SETUP #0

1. To restore the instrument to the setup conditions

stored at the displayed memory location, press
ENTER. The instrument will return to the SETUP
MENU.

2. To restore the instrument to the setup conditions

stored at a different memory location, key in the
memory location (0 to 9) and press ENTER. The in-
strument will return to the SETUP MENU. 

PWRON

 

 

Use this menu item to select the setup condi-

tions that the instrument will power-on to. To select the
PWRON menu item, place the cursor on PWRON and
press ENTER. The following menu will be displayed:

SET POWER-ON DEFAULT 

FACTORY-DEFAULT

USER-SETUP

FACTORY DEFAULT  

 

With this selection, the instru-

ment will return to the factory default conditions (see
Table 4-3) the next time it is turned on. To select the
FACTORY-DEFAULT menu item, place the cursor on
FACTORY-DEFAULT and press ENTER. The instru-
ment will return to the SETUP MENU. 

USER SETUP 

 

Using this selection, the instrument will

power-on to the setup conditions saved at a specified
memory location. To select USER-SETUP, place the cur-
sor on USER-SETUP and press ENTER. The following
typical message will then be displayed: 

 PWRON DEFAULT = #0

1. To power-on to the setup conditions stored at the

displayed memory location, press ENTER. The in-
strument will return to the SETUP MENU.

2. To power-on to setup conditions stored at a differ-

ent memory location, key in the memory location
(0 to 9) and press ENTER. The instrument will re-
turn to the SETUP MENU. 

RESET 

 

Use this menu item to reset the instrument to

the RESET default setup conditions (see Table 4-3). To
select RESET, place the cursor on RESET and press EN-
TER. The following message will be displayed: 

RESETTING INSTRUMENT

Press ENTER to display:

RESET COMPLETE

Press ENTER to return to the SETUP MENU.

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

GAIM Compact Troubleshooting preview
Compact
Бренд: GAIM Страницы: 2
D-Box HaptiSync Hub User Manual preview
HaptiSync Hub
Бренд: D-Box Страницы: 27
Gavita RS1 User Manual preview
RS1
Бренд: Gavita Страницы: 12
Patton electronics 6511RC User Manual preview
6511RC
Бренд: Patton electronics Страницы: 104
Yeastar Technology MyPBX Manual preview
MyPBX
Бренд: Yeastar Technology Страницы: 11
Kramer VS-421 User Manual preview
VS-421
Бренд: Kramer Страницы: 8
Micrel MIC2042 Manual preview
MIC2042
Бренд: Micrel Страницы: 15
Eaton AGswitch Instructions Manual preview
AGswitch
Бренд: Eaton Страницы: 36
Orno OR-GB-422 Quick Start Manual preview
OR-GB-422
Бренд: Orno Страницы: 2
Canoga Perkins HS8000 Quick Start Manual preview
HS8000
Бренд: Canoga Perkins Страницы: 7
GarrettCom PS14H-48VDC Installation And User Manual preview
PS14H-48VDC
Бренд: GarrettCom Страницы: 77
Lantech IPES-2208CA User Manual preview
IPES-2208CA
Бренд: Lantech Страницы: 146
hager EG170 User Instruction preview
EG170
Бренд: hager Страницы: 2
Boca BOCAHUB-16 Plus BEN220 Installation Manual preview
BOCAHUB-16 Plus BEN220
Бренд: Boca Страницы: 56
Thorn SENSALINK SENLSS V2 Installation And Commissioning Instructions preview
SENSALINK SENLSS V2
Бренд: Thorn Страницы: 2
Watchguard NX3CE12 Hardware Manual preview
NX3CE12
Бренд: Watchguard Страницы: 26
IP-COM F1226P User Manual preview
F1226P
Бренд: IP-COM Страницы: 58
Key Digital KD-VPHD4X1 Operating Instructions Manual preview
KD-VPHD4X1
Бренд: Key Digital Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды