Keithley 7001 Скачать руководство пользователя страница 195 | Manualshive

Страница: 195 / 353

background image

IEEE-488 Reference

5-76

5.13.1

:CLOSe <list>

[:ROUTe]:CLOSe <list>

Close specified channels

<list> = (@ chanlist)

where; chanlist is the specified list of channels (channel list) to be closed.

:clos (@

chanlist)

Power-up

All channels open

*RST

No effect

:SYSTem:PRESet

No effect

:CLOSe? <list>

Query state of specified channels.

Short-form formats:

:clos? (@ chanlist)

Response message:

1 = specified channel(s) closed.

0 = specified channel(s) not closed.

The :CLOSe command is used to close the channel(s) specified by the channel list (chanlist) in
the <list> parameter. The following examples demonstrate various forms for expressing channel
entries for a chanlist.

Chanlist

1!2!4

Single channel (Slot 1, Row 2, Column 4).

2!36

Single channel (Slot 2, Channel 36).

1!6, 1!18, 2!3!6

Multiple channels separated by commas.

1!2:1!10

Range of channels (2 through 10).

1!2:1!10, 2!3!6

Range entry and single entry separated by commas.

1!30:1!40, 2!1:2!10

Range of multiplex channels (last 10 channels on card 1,
first 10 channels on card 2).

1!4!1:1!4!10, 2!1!1:2!4!10

Range of matrix channels (10 columns of row 4 on card 1,
10 columns of row 1 on card 2).

M36

Channel pattern stored at memory location M36.

The :CLOSe? <list> query command is used to determine the state (closed or not closed) of each
specified channel. After sending this command and addressing the Model 7001 to talk, the val-
ues for the specified channels will be sent to the computer. A value of “1” indicates that the chan-
nel is closed, and a “0” indicates that the channel is not closed (open).

For example, assume channels 2, 3 and 6 are closed and the following query command is sent:

:clos? (@

1:10)

Parameter

Short-form

formats

Defaults

Query

command

Description

[:ROUTe] subsystem

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

«
...
193
194
195
196
197
...
»

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

Бренд: Barksdale Страницы: 5

Бренд: Jasco Страницы: 2

FLOW BOSS VFB-DSU

Бренд: VADA Страницы: 17

MatrixPRO 8x8 DVI

Бренд: Barco Страницы: 2

Бренд: Eaton Страницы: 5

Бренд: Endress+Hauser Страницы: 25

SI1P-SH-DVI-UCAC

Бренд: Black Box Страницы: 16

Бренд: N-Tron Страницы: 15

Бренд: NeoPro Страницы: 36

Бренд: APG Страницы: 7

Wormhole Station JUH-320

Бренд: j5 create Страницы: 9

Бренд: Clinton Electronics Страницы: 2

Бренд: DigitaLinx Страницы: 4

Бренд: Lanpro Страницы: 19

Бренд: U-Fairy G.R. IOT Tech Страницы: 3

Бренд: QNAP Страницы: 48

Arbitrator WV-TW37003

Бренд: Panasonic Страницы: 5

Бренд: Panasonic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды