manualshive.com logo in svg

Keithley 7001, Инструкция по эксплуатации

Keithley 7001 - многофункциональный коммутационный/измерительный главный фреймворк. Руководство пользователя доступно для быстрого доступа и скачивания на нашем сайте. Скачивайте бесплатно Руководство по быстрому доступу для Keithley 7001 с нашего веб-сайта manualshive.com.

Поделиться
Скачать
background image

Getting Started

3-21

:ARM:LAYER2:SOURCE MANUAL

:ARM:LAY2:SOUR MAN

:arm:layer2:source manual

:arm:lay2:sour man

:Arm:Lay2:Sour Man

:ArM:LaY2:SouR MaN

Parameters

As  previously  mentioned,  a  parameter  is  separated
from  the  command  word  by  a  space.  The  parameter
can consist of one or more data types such as channel
list, real, integer, string, name or boolean. Examples:

1. :open (@ 1!1, 1!2)
2. :open all
3. :scan (@ 1!1:1!10)
4. :trigger:count:auto on
5. :trigger:delay 0.5

1. (@ 1!1, 1!2) 

 This list parameter is used to specify

a Channel List. Parentheses ( ) are used to enclose
the list of channels. The @ symbol must precede the
first channel in the list. The exclamation point (!) is
a SCPI delimiter used to separate the slot number
from  the  card  relay  number.  Each  channel  in  the
list must be separated by a comma (,).

2. All 

 This name parameter can instead be used as

the parameter for the :OPEN command if you wish
to open all channels.

3. (@ 1!1:1!10) 

 This list parameter is used to specify

a Scan List. This is the same type of parameter used
in Example 1. In this example, Channels 1 through
10 are specified. Notice that the colon (:) is used as
a separator for the range limits.

4. On 

 This boolean parameter is used to enable an

automatic scan list count. A “1” could have instead
been used. “Off” or “0” will disable the function.

5. 0.5 

  This  real  number  parameter  sets  the  delay

period in seconds.

Multiple commands

Multiple commands can be sent in the same message as
long as they are separated by semicolons (;). For exam-
ple:

Instead of sending...

:system:error?

:system:preset

You can send ...

:system:error?;preset

When  the  above  message  is  sent,  the  first  command
word  is  recognized  as  the  root  command.  When  the
path pointer sees the colon (:) after the semicolon (;), it
resets to the root and starts over.

Proper use of the path pointer allows commands in the
same command level to be serviced without having to
re-type  the  entire  command  path.  For  example,  the
command :ARM:LAYer2:SOURce MANual moves the
path  pointer  down  to  the  last  command  level  in  the
path.  As  a  result,  the  :COUNt,  :DELay,  and  :TIMer
commands and their companion query commands can
be included in the same program message without re-
peating the entire path. Examples:

Instead of sending...

:arm:lay2:sour man;:arm:lay2:sour?

You can send ...

:arm:lay2:sour man;sour?

Instead of sending...

:trig:coun 1;:trig:del 1;:trig:tim 1

You can send ...

:trig:coun 1;del 1;tim 1

Notice that the colon (:) for the additional commands is
not included. Remember, when a colon (not preceeded
by a semicolon) is seen, the path pointer moves down
to the next command level. For example:

:trig:del 1;coun:auto on

When  this  message  is  sent,  the  path  pointer  moves
down one command level for the DELAY and COUNT
commands.  The  colon  after  the  COUNT  command
then  moves  the  pointer  down  to  the  next  command
level and enables AUTO.

Artisan Scientific - Quality Instrumentation ... Guaranteed  |  (888) 88-SOURCE  |  www.artisan-scientific.com

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

Quick TMS Manual Of Installation And Use preview
TMS
Бренд: Quick Страницы: 28
Camozzi CSD Series Use And Maintenance Instructions preview
CSD Series
Бренд: Camozzi Страницы: 2
ifs POC2502 Series User Manual preview
POC2502 Series
Бренд: ifs Страницы: 352
PRO SIGNAL PSG3450 Manual preview
PSG3450
Бренд: PRO SIGNAL Страницы: 5
Baxall DVS24 Installation And Operating Instructions Manual preview
DVS24
Бренд: Baxall Страницы: 33
Enterasys RoamAbout RBT-4102-BG Installation Manual preview
RoamAbout RBT-4102-BG
Бренд: Enterasys Страницы: 72
Dahua PFS3106-4P-60 User Manual preview
PFS3106-4P-60
Бренд: Dahua Страницы: 15
Omega iServer MicroServer EIS-2B User Manual preview
iServer MicroServer EIS-2B
Бренд: Omega Страницы: 68
Kramer VS-121HC User Manual preview
VS-121HC
Бренд: Kramer Страницы: 33
MiLAN MIL-S8TA User Manual preview
MIL-S8TA
Бренд: MiLAN Страницы: 13
rtd IDAN-LAN25255HR User Manual preview
IDAN-LAN25255HR
Бренд: rtd Страницы: 24
Xantech 686-10 Installation Instructions preview
686-10
Бренд: Xantech Страницы: 5
Guardmaster PROSAFE RKSE Series Manual preview
PROSAFE RKSE Series
Бренд: Guardmaster Страницы: 4
Delton PW03W Quick Start Manual preview
PW03W
Бренд: Delton Страницы: 2
ASCO POWER TECHNOLOGIES C2ADTL User Manual preview
C2ADTL
Бренд: ASCO POWER TECHNOLOGIES Страницы: 25
OEZ BD250NE305-250-V Instructions For Use Manual preview
BD250NE305-250-V
Бренд: OEZ Страницы: 25
Atlas WPD-SWCC Owner'S Manual preview
WPD-SWCC
Бренд: Atlas Страницы: 4
Pulsar PSB1002435 Quick Manual preview
PSB1002435
Бренд: Pulsar Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды