Keithley 7001 Скачать руководство пользователя страница 270 | Manualshive

Страница: 270 / 353

background image

7-3

7.4

Routine maintenance

The following procedures summarize routine mainte-
nance for the Model 7001. These procedures require
disassembly of the instrument (also see paragraph 7.5).

7.4.1 Line voltage selection

The Model 7001 power supply board automatically ad-
justs to line voltage and frequency. There are no inter-
nal switches for this purpose.

7.4.2 Changing the fuse

WARNING

Disconnect the instrument from the
power line and all other equipment
before replacing the line fuse.

The Model 7001 uses a single fuse which is mounted on
the power supply board. This board is located on the
underside of the instrument, immediately beneath the
power switch pushrod.

Replacement of the fuse requires removal of the instru-
ment case. The snap-in fuse can be replaced without re-
moving the power supply board.

If the fuse should fail, try to determine the cause before
installing the replacement. The correct fuse type is as
follows:

CAUTION

Use only the speci

Þ

ed fuse type, or

instrument damage may occur.

Line voltage

Type

Rating

All

5

×

20mm

250V, 2A - Fast Blow

7.4.3 Changing the battery

WARNING

Disconnect the instrument from the
power line and all other equipment
before changing the battery.

The volatile memories in the Model 7001 are protected
by a replaceable battery when power is off. Typical life
for the battery is approximately ten years. This battery
should be suspected if the instrument no longer retains
scan lists or other user-programmed operating param-
eters. If the battery is absent or totally exhausted, the
display will show the message “No Comm Link”
shortly after the Model 7001 is switched on. (This is just
one of the causes of the “No Comm Link” message. See
paragraphs 7.7.1 and 7.8.1 for more causes.)

The battery is a 3V wafer-type lithium cell, Duracell
type DL2450 or equivalent (Keithley part number BA-
44), which is located on the digital board.

Replacement of the memory back-up battery requires
removal of the instrument case, followed by removal of
the digital board and its shield. (See paragraph 7.5 for
the disassembly procedure.)

WARNING

The precautions below must be fol-
lowed to avoid possible personal in-
jury.

1. Wear safety glasses or goggles when working with

lithium batteries.

2. Do not short the battery terminals together.
3. Keep lithium batteries away from all liquids.
4. Do not attempt to recharge lithium batteries.
5. Observe proper polarity when inserting the bat-

tery into its holder.

6. Do not incinerate or otherwise expose the battery

to excessive heat (>60°C).

7. Bulk quantities of lithium batteries should be dis-

posed of as a hazardous waste.

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

«
...
268
269
270
271
272
...
»

Содержание 7001


































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 7001

Бренд: X10 Страницы: 20

Бренд: Sarowin Страницы: 9

Бренд: 3Com Страницы: 62

Elinx EIR510-2MC-T

Бренд: B&B Electronics Страницы: 107

Antenna-Disconnect-Switch

Бренд: ADS Страницы: 12

iBootBar iBB-DC8

Бренд: Dataprobe Страницы: 36

Бренд: Generac Power Systems Страницы: 2

OSD2251P Series

Бренд: Optical Systems Design Страницы: 48

Бренд: The Siemon Company Страницы: 2

CTRLink EISK8P-GT

Бренд: Contemporary Controls Страницы: 4

Бренд: Extron electronics Страницы: 6

ScatterBox POE308

Бренд: System Q Страницы: 2

iMatrix H44H150

Бренд: infobit Страницы: 27

Бренд: ProSum Страницы: 92

Бренд: Audioplex Страницы: 8

MPD-DS-WML-NFDS Series

Бренд: Larson Electronics Страницы: 2

UltraLink Lite UL-LV3

Бренд: Rose electronics Страницы: 2

Бренд: CYP Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды