Keba D3-DA 3 Series Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 120

background image

D3-DA 3xx/x

Safety notes

Project engineering manual V1.07

18

© KEBA

2.3

Safety instructions for personal safety

WARNING!

Danger of personal injury due to electric shock

●

Cut-off control from all power supplies during installation and service. If
the D3-DA 3xx/x is supplied by a D3-DP 3xx/x whose both supply termi-
nals (Line IN and Line IN Aux) must be separated from power (e.g. via
switching a joint main switch mechanism).

●

If the D3-DA 3xx/x is supplied by a D3-DP 3xx/x 3 minutes have to be
waited after switching-off due to dangerous residual voltage at the d.c.
link. Afterwards the absence of voltage has to be verified. Only then the
supply rails and the remaining covers may be opened.

●

Protective low voltage circuits must always be installed safely insulated
separated from circuits with dangerous voltage.

WARNING!

Dangerous voltage may be applied to the device, even if the device does
not emit any visual or audible signals/indications!

CAUTION!

Protection against magnetic and/or electromagnetic fields during in-
stallation and operation!

Persons fitted with heart pacemakers, metallic implants and hearing aids
etc. must not be allowed access to the following areas:

●

Areas where drive systems are installed, repaired and operated.

●

Areas where motors are installed, repaired and operated. Motors with
permanent magnets pose a particular hazard.

If it is necessary to access such areas, suitability to do so must be deter-
mined beforehand by a doctor.

2.4

Safety instructions for device maintenance

WARNING!

●

If this device is damaged, the device must be taken out of commission
and repaired or replaced by trained specialized personnel.

●

The device must only be opened by trained specialized personnel. They
must only carry out maintenance work that is explicitly permitted by
KEBA (see chapter "Maintenance").

«
...
16
17
18
19
20
...
»

Содержание D3-DA 3 Series

























































































































Отзывы:

Нет отзывов

Похожие инструкции для D3-DA 3 Series

Бренд: Lattice Semiconductor Страницы: 30

Бренд: WAFER Страницы: 15

Бренд: C&K systems Страницы: 2

Бренд: Bartlett Страницы: 5

Бренд: jbc Страницы: 4

Бренд: jbc Страницы: 4

Бренд: M-system Страницы: 103

Бренд: M-system Страницы: 18

Бренд: M-system Страницы: 7

Бренд: Radware Страницы: 98

Бренд: RabbitCore Страницы: 34

Бренд: Bardiani Страницы: 96

Бренд: Eaton Страницы: 4

Бренд: Elotech Страницы: 20

Бренд: Intermatic Страницы: 2

Бренд: Mitsubishi Страницы: 30

nERGY bluePRINT ENGCP15001

Бренд: Soundoff Signal Страницы: 5

Controller CR100

Бренд: Sonos Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды