Note:
1. The shift fork of the speed drum is installed in the
main and auxiliary shaft positions.
2. Do not install gaskets of starting shaft and auxiliary
shaft.
Installation of crankcase
The installation steps of crankcase are as follows:
1. Install the positioning pin into the corresponding hole
in the left box, and then install the crankcase gasket on
the left crankshaft box, close the right box on the left
box, turn the box, the bolt GB5783 M6x16 and gasket
6×17×2 combination and then load into the variable
speed drum threaded hole, then fasten the bolt with the
T-shaped sleeve, and turn the secondary shaft when
fastening, Determine the vice axis rotation flexibility;
Tightening torque: 12-16N·m
Note: The main and secondary axes rotate flexibly
without clamping.
2. Insert four GB/ T5777-M6x65 bolts, two GB/
T5777-M6x6 bolts, and one GB/T5787 / M6x50 bolts
Bolts pass through the corresponding bolt holes in the
left body and tighten them; Tightening torque: 10 ~ 14
N·m.
3. Install rubber plug, baffle and 1 GB/T 5787/ M6x12
bolt at the variable speed drum hole and tighten and turn
the engine over.
Note: the bolts are not loose, and the auxiliary shaft is
flexible without clamping.
4. Rotate the spindle clockwise to make the spindle turn,
the starting shaft return spring and return spring seat
combination, the spring hook hook spring seat limit
block into the starting shaft, with a flat driver to pull the
return spring, the spring hook is installed on the right
crankshaft box body, and the spring seat card into the
box positioning slot.
Note:
1. After being in place, check that the spindle rotates
flexibly and without sticking;
2. The marking point on the return spring seat should be
aligned with the marking point on the starting shaft.
Engine troubleshooting
For the engine to operate normally, the following four conditions must be met:
1. Good fuel: there is a certain ratio of combustible mixture in the cylinder.
2. Good spark: The spark plug gives off a strong spark at the right time.
3. Sufficient compression: there is enough compression pressure in the cylinder.
4. Valve timing: correct valve opening time.
Содержание TD125
