Kathrein UFS 925 Скачать руководство пользователя

Страница: 2 / 216

Mains cable

Make sure that the mains cable

(power supply cable) is not damaged.

Units with a damaged mains cable

must be disconnected from the mains

(unplugged at the mains power

socket) and repaired by an electrical

specialist before being used. Only

use the power supply unit supplied

(if available)!

Risk of fatal injury due to electric
shock!

Danger!

Cleaning

Disconnect the mains plug before

cleaning the unit. Only use a dry cloth

for cleaning and only clean the outer

surface. Never open the casing of the

unit.

Touching the parts inside the unit
carries a risk of death due to electric
shock!

Playing children

Make sure that children do not push

any objects into the ventilation slots.

Risk of fatal injury due to electric
shock!

Earthing

The antenna system must be

earthed as speci

ed or equipotentially

bonded.

EN 60728/11 and any national

regulations must be complied with.

Risk of voltage surges due to lightning
strikes!

Power supply voltage

Operate the unit only at the speci

mains voltage (indicated on the rear

of the unit or on the external power

supply unit). The unit may only be

connected to the mains and turned

on once it has been connected to the

Moisture, direct sunlight, heat,

naked

ames

Protect the unit against moisture,

dripping and splashed water (do

not place any

lled objects such

as vases on top of the unit). Do not

place the unit close to a heater or

expose it to direct sunlight and do

not operate it in damp locations. Only

use the unit in a moderate climate,

not in tropical conditions! Do not

place naked

ames such as candles

on top of the unit!

There is a risk of fi re!

Ventilation

The heat generated in this unit is

adequately dissipated. However,

the unit should never be installed

in a cupboard or on shelves with

inadequate ventilation. Never cover

the cooling slots on the unit (e.g.

with other equipment, magazines,

tablecloths, clothing or curtains)!

Batteries

If your unit was supplied with

batteries (e.g. for the remote control),

take care that the batteries are

not exposed to excessively high

temperatures, direct sunshine or

re. Exchange the batteries only

with types that are identical or

equivalent. Otherwise the batteries

and also the remote control may be

damaged. Also comply with the safety

instructions stated on the batteries:

There is a risk of explosion!

Warning!

antenna and to the TV set or the cable

network and PC.

If the mains voltage is too high, there
is a risk of fi re!

These two pages contain important information about operation, installation location and connection of the
unit. Read these instructions carefully before setting up the device.

Safety instructions - Important notes

Do not

cover

Содержание UFS 925

























































































































































































































Результаты поиска

Содержание UFS 925

Отзывы:

Похожие инструкции для UFS 925

Бренды по названию

Популярные бренды

Kathrein UFS 925, Руководство по эксплуатации

Результаты поиска

Содержание UFS 925

Отзывы:

Похожие инструкции для UFS 925

Бренды по названию

Популярные бренды