Karl Storz 11301 D1 Скачать руководство пользователя

Страница: 15 / 42

7. 1 BOOST-Modus

Durch langes Drücken des Schalters

, bei

bereits eingeschalteter Batterielichtquelle, gelangt

man in den BOOST-Modus, in welchem die

Helligkeit erhöht wird. Durch erneutes langes

Drücken des Schalters

wird der BOOST-Modus

wieder beendet und man wechselt wieder auf die

nominale Helligkeit zurück.
Wird der Schalter

nicht erneut betätigt, schaltet

der BOOST-Modus nach einer gewissen Zeit auf

die nominale Helligkeit automatisch zurück.

7. 2 Betriebsdauer-Ende

Das Betriebsdauer-Ende (bei leerer Batterie) wird

mit mehrmaligem Blinken der LED signalisiert.

Dem Anwender verbleiben noch mindestens

5 – 10 Minuten bevor die Batterie vollständig

entladen ist.
Dies wiederholt sich im Abstand von zwei Minuten

bis die Batterie vollständig entladen ist.

Anwendung

Application

7. 1 BOOST mode

By pressing the switch

for a long period of

time, when the battery light source is already

switched on, the user can access the BOOST

mode in which the brightness is increased.

Pressing the switch

again for a long period of

time ends the BOOST mode and returns the user

to the nominal brightness.
If the switch

is not pressed again, BOOST

mode automatically switches back to the nominal

brightness after a certain period of time.

7. 2 End of battery life

The end of the battery's life (when battery is

empty) is signaled by repeated flashing of the LED.

The user still has at least 5-10 minutes before the

battery is completely discharged.
This is repeated at two minute intervals until the

battery is completely discharged.

Aplicación

7. 1 Modo BOOST

Pulsando de forma prolongada el interruptor

en la fuente de luz a pila ya conectada se

alcanza el modo BOOST, en el que aumenta el

brillo. Si se vuelve a pulsar de forma prolongada

el interruptor

, el modo BOOST finaliza y se

retorna nuevamente al brillo normal.
Si no se vuelve a pulsar el interruptor

, tras un

tiempo determinado el modo BOOST conmuta

automáticamente al brillo normal.

7. 2 Finalización del período de

servicio

La finalización del período de servicio (debido

a pilas agotadas) se señaliza mediante la

intermitencia repetida del diodo luminoso. Al

usuario le quedan todavía de 5 a 10 minutos

como mínimo antes de que las pilas estén

completamente agotadas.
Esta señal se repite en intervalos de dos

minutos hasta que las pilas se hayan agotado

completamente.

Содержание 11301 D1











































Результаты поиска

Содержание 11301 D1

Отзывы:

Похожие инструкции для 11301 D1

Бренды по названию

Популярные бренды

Karl Storz 11301 D1, Инструкция по эксплуатации

Результаты поиска

Содержание 11301 D1

Отзывы:

Похожие инструкции для 11301 D1

Бренды по названию

Популярные бренды