manualshive.com logo in svg

Kantronics TALON UDC SERIES, Руководство пользователя, Страница: 63 / 101

Поделиться
Скачать
Kantronics TALON UDC SERIES Скачать руководство пользователя страница 63

Page 63 of 101

DWG ID: 181-0101-00A

Date: 2003-09-26

default ON

When ON, connect requests from other TALONs will be automatically acknowledged
and a <UA> packet will be sent. The standard connect message, with stream ID if
appropriate, will be output to the terminal and the mode specified by CONMODE will be
entered on the I/O stream if you are not connected to another station and NOMODE is
OFF.

When OFF, connect requests from other TALONs will not be acknowledged and a
<DM> packet will be sent to the requesting station. The message “connect request:
(callsign of whoever is trying to connect to you)” will be output to your terminal if
INTFACE is TERMINAL or NEWUSER.

When operating with multiple connects allowed, the connection will take place on the
next available stream. Connect requests in excess of the number allowed by the USERS
command will receive a <DM> response and the “connect request: (call)” message will
be output to your terminal if INTFACE is TERMINAL or NEWUSER.

See also: conmode, connect, intface, maxusers, monitor, nomode, users

CONPERM {ON | OFF}

default OFF

Setting CONPERM to ON forces the connection on the current stream to become
permanent and causes the TALON to attempt to reconnect when it is restarted.
CONPERMED connections are shown with /P in the status display, which is generated
by the STAT command.

See also: status

CONVERS

Immediate

CONVERS has no options. It is an immediate command and will cause entry into
Conversational Mode from Command Mode on the current I/O stream. Any link
connections are not affected.

Hint: K is the same as CONVERS, for quicker entry.
See also: k, command

Содержание TALON UDC SERIES






































































































Отзывы:

Нет отзывов