K-Systems G95 Скачать руководство пользователя страница 32

Страница: 32 / 38

Page 29

Instruction manual - G95

Kivex Biotec Ltd

10. User maintenace

10.1 Cleaning

The G95 is a low maintenance unit designed to be both easy to use and clean, plus it is durable due to its

construction.

All surfaces should be cleaned with a 70� alcohol solution on a clean cloth or lint-free paper towel.

Clean all surface components by wiping gently with gauze.

•

To remove fingerprints or oil smudges, wipe with gauze slightly moistened with a mixture

•

of ether (70%) and alcohol (30%).

Note

Since solvents such as ether and alcohol are highly flammable, they must be handled

carefully. Be sure to keep these chemicals away from open flames or potential sources

of ignition – for example, electrical equipment that is being switched on or off.

Also remember to always use these chemicals only in a well ventilated room.

If smudges are difficult to clean, wipe them with a soft cloth slightly moistened with a

•

diluted neutral detergent.

The heated compartment is able to withstand some water spills. However, precautions are

•

still necessary if water is spilled on the surface. Unplug the power cord, and then wipe dry

with a dry cloth immediately.

Note

If water gets inside the unit, contact your K-SYSTEMS representative to check electrical

safety.

10.2 Calibration

For optimal performance the unit should be calibrated once a year by authorized K-SYSTEMS Service

provider.

Содержание G95







































Результаты поиска

Содержание G95

Отзывы:

Похожие инструкции для G95

Бренды по названию

Популярные бренды

K-Systems G95, Инструкция по эксплуатации

Результаты поиска

Содержание G95

Отзывы:

Похожие инструкции для G95

Бренды по названию

Популярные бренды