K-Stove KS 8020HY Скачать руководство пользователя страница 38

Страница: 38 / 40

PELLET BURNING STOVES INSTALLATION & MAINTENANCE MANUAL

Heat exchange tubes are

dirty.

Clean the heat exchange tubes.

10. Showing "Pressure

Erro" on the display

Vent pipe is blocked

The door is opening

The are some leakages

Shut down the stove, check the venting pipe

Close the door and unplugged then restart

Check it and repair it.

Adjust the combustion fan's speed up to offer more pressure in

the stove

NO increase in

temperature with stove in

operation

1. Incorrect combustion

adjustment.

2. boiler/system dirty

3. Insufficient stove

power.

4.poor pellet quality

1.check recipe and parameters.

2. check and clean the boiler

3.Check that stove is properly sized for the requirements of the

system.

4. Use

EN-A1-plus certified

pellets.

Condensation in boiler

1. Incorrect temperature

setting.

2.Insufficient fuel

consumption.

1. set the stove to a higher temperature.

2.check the recipe and/or technical parameters

Radiators cold in winter

1. room thermostat (local

or remote) set too low if

remote thermostat, check

if it is defective.

2. circulator does not run

because blocked.

3. Circulator does not run.

4.radiator have air in them

1.set to higher temperature or replace.( if remote)

2. free up the circulator by removing the plug and turning the

shaft with screwdriver.

3. check the electrical connections of the circulator; replace if

necessary

4.Vent the radiators

Hot water is not provided

1. circulator (pump)

blocked

1. free the circulator (pump)

Содержание KS 8020HY









































Результаты поиска

Содержание KS 8020HY

Отзывы:

Похожие инструкции для KS 8020HY

Бренды по названию

Популярные бренды

K-Stove KS 8020HY, Инструкция по эксплуатации

Результаты поиска

Содержание KS 8020HY

Отзывы:

Похожие инструкции для KS 8020HY

Бренды по названию

Популярные бренды