K-Stove KS 8020HY Скачать руководство пользователя страница 12

Страница: 12 / 40

PELLET BURNING STOVES INSTALLATION & MAINTENANCE MANUAL

2.10. HYDRAULIC CONNECTION

IMPORTANT!

The connection of the stove to the hydraulic system must be made ONLY by qualified personnel and

can perform the installation in “ART” and in compliance with all statutory and regulatory provisions in force

and not in the country of installation. If the installation of the stove requires interaction with another existing

facility complete with another heater (gas boiler, gas boiler, oil boiler, etc ...), is recommended for more

qualified personnel who can then be challenged to answer the Full compliance of the system, per the

applicable law, and issuing the certificate. K-Stove disclaims any liability for damage to persons or property or

in the event of failure or improper operation, if not complied with the above warnings, and issued the

necessary certificates of compliance enforcement work in an appropriate manner. It is absolutely necessary

that the network is designed properly sized to dispose of all the heat flux produced by the stove to avoid

raising the temperature inside the boiler.

3. INSTALLATION AND ASSEMBLY 3.1. DRAWINGS AND SPECIFICATIONS

3.1.1. Dimensions of Hydro stoves

3.1.2. Technical data sheets

Model

KS 8020HY

SAPHIRE

Rating Voltage and Frequency

V/HZ

230V/50HZ

Maximum water pressure

Bar

1.5

Electronic consumption MAX

W/H

CO emission at 13%

oxygen(mg/m3) Max

CO emission at 13% oxygen(mg)

Min

Efficiency Max

90.5

Efficiency Min

93.9

Heat Area

495

Rating power Max/Min

20.6/6.5

Rating power(water) Max/Min

19.06/10.6

Thermal power to the environment

Max/Min

4/3.6

ΦPellet

Length of pellet

Hopper capacity

Automatic burning time Max/Min

7.5/22

Weight

185

Size(WxHxD)

630*1278*72

ΦAir outlet pipe

Temperature of the smoke output

Max/Min

°C

95.8/80

Flue draught pressure

0.1-15

Содержание KS 8020HY









































Результаты поиска

Содержание KS 8020HY

Отзывы:

Похожие инструкции для KS 8020HY

Бренды по названию

Популярные бренды

K-Stove KS 8020HY, Инструкция по эксплуатации

Результаты поиска

Содержание KS 8020HY

Отзывы:

Похожие инструкции для KS 8020HY

Бренды по названию

Популярные бренды