K-Stove KS 8020HY Скачать руководство пользователя страница 30

Страница: 30 / 40

PELLET BURNING STOVES INSTALLATION & MAINTENANCE MANUAL

4.) Safety

POWER FAILURE

After the power failure, the display will show

. If you have a short cut of power failure, you manually go back to

"Stabilization" by clearing the E7 with the "okay button"

restart the stove and then keep pressing 3 seconds on the

"fire button"

On power failure a small amount of smoke may be emitted. This does not last for more than three to five minutes and

does not represent a safety risks.

POWER INPUT SOCKET

(contains the main fuse)

ELECTRIC EXCESS-CURRENT SHUT OFF

The device is protected against excess current by a main fuse (on the rear of the stove),

The following is a list of main components and their functions

IGNITER :

The STOVE comes equipped with an automatic igniter for lighting the fuel when the stove is in feeding and

lighting mode.

VACCUM SWITCH:

The STOVE has a vacuum switch located behind the left door, fastened to the base. If a low

pressure is created in the firebox by a leak, opening the front door, a blocked flue, or unsealed ash drawer (some model), the

vacuum switch will sense it and cause the stove to go into a shutdown mode by showing E5.

AUGER AND AUGER MOTOR:

The 2.4 RPM auger motor turns the auger, lifting pellets up the auger tube. The pellets

are then dropped down a tube and into the firepot. The auger motor is controlled by the control board.

PROTECT TEMPERATURE SENSOR TO AVOID

OVERHEATING.

A safety temperature switch switches the stove off automatically if it overheats,. After the stove has cooled down

meanwhile it shows E6. Whether the heating operation is continued or not depends on the remaining embers in the

fire pan. After you remove the Error Code by "Okay button" , If re-ignition does not occur when the fuel supply

recommences, then the out of operation program (cleaning , lag phase) is carried out. According to the pre-set mode

the stove must be re-started.

CAUTION: If overheating has occurred then maintenance or cleaning work must be carried out

EXHUAST TEMPERATURE SENSOR DOES FUNCTION AS

LOW TEMPERATURE SWITCH OFF

Содержание KS 8020HY









































Результаты поиска

Содержание KS 8020HY

Отзывы:

Похожие инструкции для KS 8020HY

Бренды по названию

Популярные бренды

K-Stove KS 8020HY, Инструкция по эксплуатации

Результаты поиска

Содержание KS 8020HY

Отзывы:

Похожие инструкции для KS 8020HY

Бренды по названию

Популярные бренды