K-Stove KS 8020HY Скачать руководство пользователя страница 36

Страница: 36 / 40

PELLET BURNING STOVES INSTALLATION & MAINTENANCE MANUAL

boiler)

If after 15 mins, it does

not work, there must be

wrong

degrees on the venting pipe.

No power in stove or in the

control panel.

Or Unplugged on the mother

board

The low temperature sensor

is broken

Check the power and wires.

Plug it

Replace it

3. No feeding after 20 seconds of starting.

There are three stages for the feeding process.

One is during the several minutes, feeding is constantly. "Feeding" is showing on the LCD display

Two is the following couple minutes, the feeding light is off.:"LightIing" showing on the Display

The last stage is that feeding Every several seconds all the time after previous stages.

A. For the first stage

(during first several

minutes)

Feed unit is blocked.

Check the auger is blocked or not.

There is the problem

about the connection

between motor and auger

Check the fasten screw between auger and motor loose or not.

Or the auger might jump out

No fuel in the hopper.

Fill the fuel into the hopper.

B. For the second stage

It is normal

Please be patient

C. Regarding to the last

stage

Feed unit is blocked.

Check the auger is blocked or not.

There is the problem

about the connection

between motor and auger

Check the fasten screw between auger and motor loose or not.

Or the auger might jump out

No fuel in the hopper.

Fill the fuel into the hopper.

4. Feeding not properly

A. too much wood pellet

and cannot burned in time

The level of feeding

speed is too high

Adjust the combustion fan's speed up

Содержание KS 8020HY









































Результаты поиска

Содержание KS 8020HY

Отзывы:

Похожие инструкции для KS 8020HY

Бренды по названию

Популярные бренды

K-Stove KS 8020HY, Инструкция по эксплуатации

Результаты поиска

Содержание KS 8020HY

Отзывы:

Похожие инструкции для KS 8020HY

Бренды по названию

Популярные бренды