manualshive.com logo in svg

K-Stove KS 8020HY, Инструкция по эксплуатации, Страница: 4 / 40

Поделиться
Скачать
K-Stove KS 8020HY Скачать руководство пользователя страница 4

PELLET BURNING STOVES INSTALLATION & MAINTENANCE MANUAL

3

• If this manual should be lost or destroyed, or if still in poor condition, ask for a copy from your dealer

• A key topic or that requires special attention is high lightened in a "bold text".

• "Italic text" is used to draw your attention to other sections of this manual or for any additional clarification.

SYMBOLS ON THIS MANUAL

WARNING:

This warning symbol indicates that you read and understand the message that is reported as

the non- observance of what is written, could cause serious damage to the stove and put at 

risk the safety of the user.

INFORMATION:

This symbol is intended to emphasize the important information for the proper functioning of

the stove. A failure to comply with the requirements affect the use and operation of the

stove will prove unsatisfying.

SEQUENCE OF OPERATIONS:

Indicates a sequence of buttons to press to access the menu or make adjustments.

MANUALE (instruction manual)

Indicates you should read this manual or instructions.

1. WARNINGS AND WARRANTY
1.1. SAFETY INSTRUCTIONS

• Installation, electrical connection, check that the installation and maintenance are performed only by qualified and

authorized by K-Stove DESIGN.

• Install the heater according to the regulations of the place, region or state.

• This appliance is not intended to be used by people (including children) with reduced physical, sensory, mental, or

with limited experience and knowledge, unless they are trained to use the device or supervised by the person who is

fully responsible for his security.

• For the correct use of the stove and electronic equipment connected to it and to prevent accidents it is important to

follow and observe all indications and information and instructions reported in this manual.

• The use, regulation and settings must be carried out by an adult. Errors or bad settings can cause hazardous

conditions and / or erratic operation.

• Before starting any operation, the user or anyone who is about to operate on the stove must have read and correctly

and completely understood the entire contents of this instruction booklet.

• The stove must be intended solely for the purpose for which it is intended. Any other use is considered improper and

therefore dangerous under the full responsibility of those who make improper use, and therefore void with immediate

effect a guarantee thereof.

• Do not use the stove as a ladder or support structure.

• Do not put towels on the stove to dry.

• Any clothes or similar must be kept at a specific distance from the heater, due to possible fire hazard.

Содержание KS 8020HY









































Отзывы:

Нет отзывов