Masterpage:Right-No-Heading
Filename [DR-M1EK_10Editing.fm]
Page 81
August 29, 2003 6:40 pm
81
A
Make connections.
Connect a camcorder or DV equipment to the DV IN
connector on the unit’s front panel.
B
Prepare the unit for dubbing.
C
Press
w e
to move
0
to
, then press
ENTER
.
D
Press
rt
repeatedly to select the desired sound track,
then press
ENTER
.
●
Note that this selection is not available when the source
programme is recorded in 16BIT (48 kHz) mode.
E
Press
REC MODE
repeatedly until the desired
recording speed appears. (
墌
pg. 54, “Recording
Speed”)
C
Prepare the DV equipment for dubbing.
Locate the point from where you want to start dubbing,
then stop or pause playback by pressing the following
buttons on the remote control:
4
,
5
,
3
,
8
,
9
●
To play back in slow speed (1/10 of the normal speed), press
9
to pause playback, then press
3
or
5
.
●
To play back frame-by-frame, press
9
to pause playback, then
press
9
repeatedly. Each press of
9
advances a frame.
●
To change the playback direction, press
3
or
5
.
D
Start dubbing.
Press
w e
to move the arrow to
, then press
ENTER
.
●
Playback on the external DV equipment and recording on the
unit should start simultaneously.
●
When the playback from the beginning is not possible, the
“DV DUBBING” controller cannot be used. Perform dubbing
without using the “DV DUBBING” controller. (
墌
right
column)
●
To pause dubbing, press
w e
to move
0
to
, then
press
ENTER
. Both the unit and the external DV equipment
pause dubbing. Pressing
9
on the unit also works the same
way.
●
To clear the “DV DUBBING” controller from the TV screen,
press
PLAY SET UP
.
E
Stop dubbing.
Press
8
on the remote control.
●
Both the unit and the external DV equipment stop dubbing.
NOTES:
●
Dubbing copyright guarded programmes is not possible.
●
Original DV informations such as the recording date and time
are not recorded.
●
The superimposed indication during the operation or dubbing
is not recorded.
●
The “DV DUBBING” controller disappears if
SET UP
or other
buttons are pressed. To display the “DV DUBBING” controller
again, press
PLAY SET UP
on the remote control.
Performing dubbing without using the “DV DUBBING”
controller
A
Press
PR +/–
to set the channel to “DV DUBBING”.
B
Press
REC MODE
repeatedly until the desired recording
speed appears.
C
Start playback on the external DV equipment slightly before
the actual point from where you wish to start dubbing.
D
Press and hold
7
, then press
4
on the remote control, or
press
7
on the unit.
●
Dubbing starts.
E
When the dubbing ends, press
8
on the unit, then stop
playback on the external DV equipment.
A
Load a DVD-RAM/RW/R
disc on the unit.
B
Press
PR +/–
to set the
channel to “DV
DUBBING”.
●
The “DV DUBBING”
controller appears on the TV
screen.
AUDIO 1
:
Select this to record the original stereo sound
played back on the connected DV equipment.
AUDIO 2
:
Select this to record the dubbed stereo sound
played back on the connected DV equipment.
MIX
:
Select this to record the sound of both
“AUDIO 1” and “AUDIO 2”.
DR-M1EK_10Editing.fm Page 81 Friday, August 29, 2003 6:41 PM
