Filename [M150SEK_05Name.fm]
Masterpage:Left0
16
EN
INSTALLING YOUR NEW UNIT
It’s essential that your unit be properly connected.
1
Place the unit on a stable, horizontal surface.
2
Connect the unit to a TV depending on the TV and cables you
use.
8
Basic Connection
To connect to a TV with 21-pin SCART input connector
^
A
Disconnect the TV aerial cable from the TV.
B
Connect the TV aerial cable to the [ANTENNA IN] connector on
the rear panel of the unit.
C
Connect the [ANTENNA OUT] connector on the rear panel of
the unit and the TV’s aerial connector with the supplied RF
cable.
D
Connect the [L-1 IN/OUT] connector on the rear panel of the
unit and the TV’s 21-pin SCART connector with a supplied 21-
pin SCART cable.
●
The [L-1 IN/OUT] connector accepts and delivers either a
composite signal (regular video signal), Y/C signal or RGB
signal.
●
Set your TV to the VIDEO, Y/C, or RGB mode according to the
type of your TV’s SCART connector.
8
Component Video Connection
To connect to TV’s component video input connectors
^
A
Perform steps
A
-
C
of
A
Basic Connection
B
.
B
Connect the unit’s [COMPONENT VIDEO OUT (Y/P
B
/P
R
)]
connectors to the TV’s component video input connectors.
C
Connect the unit’s [AUDIO OUT] connectors to the TV’s AUDIO
input connectors.
●
You can obtain high-quality component video pictures.
●
If your TV is not stereo-capable, use the unit’s [AUDIO OUT]
connectors to connect to an audio amplifier for Hi-Fi stereo
sound reproduction.
●
By using the component video connection, you can view the
images in the progressive mode. For switching to the
progressive mode, refer to
A
Scan Mode Set
B
(
A
pg. 63).
NOTE:
Select an appropriate option of
A
L-1 OUTPUT
B
as follows
(
A
pg. 57):
●
When the setting selected is not in accordance with the TV
connected and depending on the type of appliance connected
to the unit, the correct picture will not appear.
●
This unit only supports 625i/625p PAL signals. Other modes are
not receivable.
3
Plug the end of the mains power cord into a mains outlet.
●
A
PLEASE
B
and
A
WAIT
B
blink alternately on the front display
panel when the AC plug of the mains power cord is connected
into a mains outlet. And it takes approximately 30 seconds for
the unit to be turned on. This is not a malfunction.
Basic Connection
ATTENTION:
●
Your TV must have a 21-pin AV input connector (SCART) for
the basic connection to the unit.
●
Connect the AC plug only after all connections to the TV has
been completed.
TV aerial cable
Mains outlet
Back of unit
Component
video cable
(not supplied)
TV
Mains power cord
Audio cable
(not supplied)
To
[COMPONENT
VIDEO OUT
(Y/P
B
/P
R
)]
To [AUDIO
OUT]
To [ANTENNA IN]
To
[ANTENNA
OUT]
RF cable
(supplied)
To [L-1 IN/OUT]
21-pin SCART
Cable
(supplied)
To 75 ohm terminal
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
When your TV’s SCART
connector accepts:
Set
A
L-1 OUTPUT
B
to:
Composite signals
A
SCART VIDEO
B
Y/C signal (separated
luminance (brightness) and
chrominance (colour) signals)
A
SCART S-VIDEO
B
RGB signal
A
SCART RGB
B
Component video signal
A
COMPONENT
B
If you possess a satellite receiver, refer to
A
Connecting To A
Satellite Receiver
B
as well. (
A
pg. 59)
M150SEK_00.book Page 16 Wednesday, June 15, 2005 4:04 PM
