Jungheinrich ETVC 16, Руководство по эксплуатации

Страница: 71 / 89

120
7.GB
F 14
7.3 Recommissioning the truck
– Thoroughly clean the truck.
– Lubricate the truck according to the lubrication chart (refer section 5).
– Clean the battery. Grease the pole screws using pole grease and reconnect the
battery.
– Recharge the battery (refer to chapter D).
– Check if the gear oil contains condensed water and change, if required.
– Check if the hydraulic oil contains condensed water and change, if required.
– Start up the truck (refer to chapter E).
Z
If switching troubles are experienced in the electric system, spray the exposed con-
tacts with contact spray and remove a possible oxide layer on the contacts of the ope-
rating controls by repeated operation.
F
Perform several brake tests immediately after recommissioning the truck.
8 Safety checks to be performed at regular intervals and following any untoward
incidents (
D : Accident prevention check according to BGV D27)
At least once yearly, or after any untoward incident, the truck has to be checked by a
qualified inspector. The inspector must assess the condition of the truck from a stand-
point purely concerned with safety aspects, uninfluenced by any company or econo-
mic circumstances. The inspector must be adequately informed and experienced to
be able to assess the condition of the truck and the effectiveness of the safety instal-
lations based on the technical rules and principles governing the inspection of trucks.
The inspection must comprise a comprehensive check of the technical condition of
the truck with regard to accident prevention aspects. Apart from this, the truck must
be thoroughly inspected for damage possibly caused by incorrect use of the truck.
The inspection results must be recorded in an inspection report which has to be kept
available for a period spanning at least the next two inspection intervals.
The user has to ensure that all defects are eliminated without delay.
Z
The manufacturer has set up a special safety service with specially qualified staff. As
visual proof that the truck has passed the safety inspection, a plaque will be affixed
to it. This plaque indicates in which month of which year the next test will be due.
120
7.GB
F 14
7.3 Recommissioning the truck
– Thoroughly clean the truck.
– Lubricate the truck according to the lubrication chart (refer section 5).
– Clean the battery. Grease the pole screws using pole grease and reconnect the
battery.
– Recharge the battery (refer to chapter D).
– Check if the gear oil contains condensed water and change, if required.
– Check if the hydraulic oil contains condensed water and change, if required.
– Start up the truck (refer to chapter E).
Z
If switching troubles are experienced in the electric system, spray the exposed con-
tacts with contact spray and remove a possible oxide layer on the contacts of the ope-
rating controls by repeated operation.
F
Perform several brake tests immediately after recommissioning the truck.
8 Safety checks to be performed at regular intervals and following any untoward
incidents (
D : Accident prevention check according to BGV D27)
At least once yearly, or after any untoward incident, the truck has to be checked by a
qualified inspector. The inspector must assess the condition of the truck from a stand-
point purely concerned with safety aspects, uninfluenced by any company or econo-
mic circumstances. The inspector must be adequately informed and experienced to
be able to assess the condition of the truck and the effectiveness of the safety instal-
lations based on the technical rules and principles governing the inspection of trucks.
The inspection must comprise a comprehensive check of the technical condition of
the truck with regard to accident prevention aspects. Apart from this, the truck must
be thoroughly inspected for damage possibly caused by incorrect use of the truck.
The inspection results must be recorded in an inspection report which has to be kept
available for a period spanning at least the next two inspection intervals.
The user has to ensure that all defects are eliminated without delay.
Z
The manufacturer has set up a special safety service with specially qualified staff. As
visual proof that the truck has passed the safety inspection, a plaque will be affixed
to it. This plaque indicates in which month of which year the next test will be due.