JUKI SC-922 страница 6 Скачать руководство пользователя

Страница: 6 / 58

– 4 –

6. Installation and adjustment for the protecting pin and the belt slip-off preventing

bracket

WarNING :

to protect against possible personal injury due to abrupt start of the machine, be sure to start the

following work after turning the power off and ascertaining that the motor is at rest.

Belt

attaching

hole

attaching
hole

4 mm or less

Belt

4 mm or less

adjusting position for protecting pin

Pulley

cover

Motor

pulley

3 mm or less

adjusting position for belt slip-off preventing bracket

Belt

1) Attachng hole for the protectng pn
To attach protectng pn

, select ether attachng

hole

or attachng hole

n the motor pulley

cover n accordance wth the drecton of rotaton
of the sewng machne and attach the pn n the
selected hole usng screw

and washer

sup-

pled wth the unt.

a)) If the motor shaft rotates n drecton A n the

figure on the above:

Attach protectng pn

n attachng hole

b) If the motor shaft rotates n drecton B n the

figure on the above:

Attach protectng pn

n attachng hole

2) Adjustment for the protectng pn and the belt

slp-off preventng bracket

Adjust the poston of protectng pn

and belt

slp-off preventng bracket

n accordance wth

the figure on the left.

a) Adjustng the protectng pn
Loosen screw

and adjust so that protectng

s postoned at the locaton ndcated

in the figure on the left.

b) Adjustng belt slp-off preventng bracket
Loosen screw

and adjust so that belt slp-

off preventng bracket

s postoned at the

location indicated in the figure on the left.

If protectng pn

s not properly adjusted,

it is possible that your fingers may be caught

n the clearance provded between the pulley
and the belt resultng n njury. If belt slp-off
preventng bracket

s not properly ad-

justed, t s possble to allow the belt to slp off
causng safety hazard.

3) After the adjustment, tghten screws

and

so as to secure protectng pn

and belt slp-off

preventng bracket

to prevent these compo-

nents to fluctuate because of vibration.

4) Before startng the operaton of the sewng ma-

chne, ascertan that protectng pn

and belt

slp-off preventng bracket

do not come n

contact wth the pulley and the belt.

Содержание SC-922



























































Результаты поиска

Содержание SC-922

Отзывы:

Похожие инструкции для SC-922

Бренды по названию

Популярные бренды

JUKI SC-922, Инструкция по эксплуатации

Результаты поиска

Содержание SC-922

Отзывы:

Похожие инструкции для SC-922

Бренды по названию

Популярные бренды