JUKI SC-922 страница 50 Скачать руководство пользователя

Страница: 50 / 58

– 48 –

11. Setting of the auto lifter function

1) Turn ON the power swtch wth

swtch

held pressed.

2) "FL ON" s dsplayed on ndcators

and

wth a blp to make the auto

lfter functon effectve.

3) Turn OFF the power swtch, and turn

ON the power swtch agan to return

to the normal mode.

4) Repeat the operaton 1) to 3), and

LED display is turned to (FL OFF).

Then, the functon of auto-lfter does

not work.

FL ON : Auto-lifter device becomes effective. Selection of the auto-lifter device of solenoid drive (+33V)

or of air drive (+24V)

can be performed wth

swtch

(Changeover is performed to drive power +33V or +24V of CN37.)

FL OFF : Auto-lfter functon does not work. (Smlarly, the presser foot s not automatcally lfted when pro-

(Smlarly, the presser foot s not automatcally lfted when pro-

grammed sttchng s completed.)

Solenoid drive display (+33V)

air drive display (+24V)

(Caution) 1. to perform re-turning oN of the power, be sure to perform after the time of one second or

more has passed.

(If oN / oFF operation of the power is performed quickly, setting may be not changed

over well.)

2. auto-lifter is not actuated unless this function is properly selected.

3. When “FL oN” is selected without installing the auto-lifter device, starting is momentarily

delayed at the start of sewing. In addition, be sure to select “FL oFF” when the auto-lifter

is not installed since the touch-back switch may not work.

WarNING :

When the solenoid is used with the air drive setting, the solenoid may be burned out. So, do not

mistake the setting.

When the auto-lifter device (AK) is attached, this function makes the function of auto-lifter work.

Содержание SC-922



























































Результаты поиска

Содержание SC-922

Отзывы:

Похожие инструкции для SC-922

Бренды по названию

Популярные бренды

JUKI SC-922, Инструкция по эксплуатации

Результаты поиска

Содержание SC-922

Отзывы:

Похожие инструкции для SC-922

Бренды по названию

Популярные бренды