JUKI SC-922 страница 54 Скачать руководство пользователя

Страница: 54 / 58

– 52 –

. MaINtENaNCE

1. removing the rear cover

WarNING :

to prevent personal injuries caused by electric shock hazards or abrupt start of the sewing machine,

remove the cover after turning oFF the power switch and a lapse of 5 minutes or more.

to prevent

personal injuries, when a fuse has blown out, be sure to replace it with a new one with the same

capacity after turning oFF the power switch and removing the cause of the blown-out of the fuse.

1) Press the OFF button of the power swtch to turn

OFF the power after confirming that the sewing

machne has stopped.

2) Draw out the power cord coming from the power

plug socket after confirming that the power switch

s turned OFF. Perform the work of step 3) after

confirming that the power has been cut and it has

passed for 5 mnutes or more.

2. replacing the fuse

(Caution) the illustration below shows the PWr-t PCB. the type of PCB differs by destination.

1) Remove all the cables

whch are connected to

the control box.

2) Remove the connectng

rod.

3) Remove the control box

from the table stand.

4) Holdng the glass sec-

ton of fuse

, remove

the fuse.

(Caution) there is a risk of electrical shock when removing the fuse. Be sure to remove the fuse after

LED

has totally gone out.

5) Be sure to use a fuse wth the desgnated capacty.

: 3.15 A/250 V Tme-lag fuse (Power crcut protectve fuse)

Part number: KF000000080

6) Install the control box on the table stand. (Refer to

. SEt-uP" p. 1

7) Connect all the cables to the control box. (Refer to

-7. Connecting the cords" p. 5

8) Ft the connectng rod back n place. (Refer to

-8. attaching the connecting rod" p. 13

3) Loosen setscrew

n cover

. Open cover

4) To close cover

, re-tghten setscrew

whle

payng attenton to the orentaton of cable clp

band

mounted on the side face of the box.

Содержание SC-922



























































Результаты поиска

Содержание SC-922

Отзывы:

Похожие инструкции для SC-922

Бренды по названию

Популярные бренды

JUKI SC-922, Инструкция по эксплуатации

Результаты поиска

Содержание SC-922

Отзывы:

Похожие инструкции для SC-922

Бренды по названию

Популярные бренды