JUKI MO-6800D/DD20 Series, Инструкция по эксплуатации

Страница: 39 / 77

– 36 –
No Item Description Range
Initial value
DD22 DD23
P049 Automatic suction ON / OFF Type of operation of the automatic suction can be selected with this function setting number.
(0: OFF / 1: Front suction / 2: Rear suction /3: Front and rear suction)
0-3 3 3
P050 Front suction, continuing number of
stitches
This function setting number is used for setting the number of stitches to be sewn continuously
until the front suction stops after the intermediate sensor has detected the material.
(Unit: stitch)
0-50 5 5
P051 Intermediate suction, continuing
number of stitches
This function setting number is enabled only in the case "DD22" is selected with the function
setting number "P125 Model selection".
This function setting number is used for setting the number of stitches to be sewn continuously
until the rear suction stops after the material has passed the intermediate sensor. (Unit: stitch)
0-50 35 5
P052 Intermediate suction, starting num-
ber of stitches
This function setting number is enabled only in the case "DD22" is selected with the function
setting number "P125 Model selection".
This function setting number is used for setting the delaying number of stitches to be sewn be -
fore the rear suction starts after the material has passed the intermediate sensor. (Unit: stitch)
0-50 0 0
P053 Rear suction, duration This function setting number is enabled only in the case "DD23" is selected with the function
setting number "P125 Model selection".
This function setting number is used for setting the duration of suction until the rear suction is
stopped after the rear thread trimmer has started. (Unit: ms) If the rear thread trimmer is set to
"OFF", the rear suction will not operate.
0-5000 200 200
P054 Manual suction ON / OFF It is possible to select the type of operation of manual suction to be carried out by pressing the
hand switch. (0: OFF / 1: Rear suction / 2: Front and rear suction)
0-2 1 1
P055 Manual suction, duration This function setting number is used for setting the duration of suction until the suction (set
with P054) is stopped by pressing the hand switch. (Unit: ms)
0-2000 500 500
P056 Low pressure mode ON / OFF If the supplied air pressure is low, set this function setting number to "ON". Then, the function
set with the function setting number P057 is enabled. (0: OFF / 1: ON)
0-1 0 0
P057 Suction synchronization time This function setting number is enabled when "P056 Low pressure mode" is set to "ON". The
device connected to Suction 2 will operate simultaneously with the device connected to Suc-
tion 1 during the time set with this function setting number. (Unit: ms)
0-2000 200 200
P058 Continuous material feeding section
ON / OFF
It is possible to select the type of operation of the device connected to Suction 2.
(0: OFF / 1: Long suction / 2: Synchronized suction / 3: Intermittent suction (controlled by time)
/ 4: Intermittent suction (controlled by the number of stitches))
Refer to the Engineer's Manual for how to connect the device to Suction 2.
0-4 2 2
P059 Intermittent suction, time This function setting number is enabled when P058 is set to "3: Intermittent suction (controlled
by time)". The operating time of the intermittent suction. (Unit: x100ms)
1-600 2 2
P060 Intermittent suction, duration This function setting number is enabled when P058 is set to "3: Intermittent suction (controlled
by time)". The operating time of the intermittent suction. (Unit: x100ms)
1-600 2 2
P061 Intermittent suction, the number of
stitches
This function setting number is enabled when P058 is set to "4: Intermittent suction (controlled
by the number of stitches)". The number of stitches to be sewn while operating the intermittent
suction. (Unit: stitch)
0-200 50 50
P062 Intermittent suction, stopping num-
ber of stitches
This function setting number is enabled when P058 is set to "4: Intermittent suction (controlled
by the number of stitches)". The number of stitches to be sewn while operating the intermittent
suction. (Unit: stitch)
0-200 50 50
P066 Auto lifter ON / OFF It is possible to select the type of operation of the auto lifter with this function setting number.
(0: OFF / 1: Front lifter / 2: Rear lifter / 3: Front and rear lifters)
0-3 0 0