JUKI HZL-35Z Скачать руководство пользователя

Страница: 29 / 34

SECTION
PAGE

( 5 )

( 4 )

( 6 )

( 7 )

( 8 )

( 4 )

2 - 20
1

2 - 20 Hooking Fork Position of Needle Threader

Adjustment when hook (1) is deviated vertically:

1. Remove face cover.

2. Turning hand wheel by hand, bring needle bar to its highest

position.

3. Lower needle hole threader lever (3).
4. Pushing needle hole threader lever (3) away from you,

insert hook (1) into needle hole, and keep it.

5. Loosen stopper screw (4).
6. Holding threader stopper (4) onto stopper pin (8), tighten stopper screw (5).

Make sure to align the screw (5) with the screw (7) on needle bar clamp (6)

Checking:

1. Check and see if #14 needle is used and it is not bent.
2. Set machine for Straight Stitch at center needle

position.

3. Raise the needle to its highest position by rotating

the hand wheel towards you.

4. Lowering needle hole threader lever, check and

see if hook (1) inserts into needle hole.

Adjustment when hook (1) is deviated horizontally or bent vertically:

Correct the condition using small screw driver as illustrated.

Center

( 3 )

( 1 )

Deviated horizontally

Bent vertically

Содержание HZL-35Z



































Результаты поиска

Содержание HZL-35Z

Отзывы:

Похожие инструкции для HZL-35Z

Бренды по названию

Популярные бренды

JUKI HZL-35Z, Руководство по обслуживанию

Результаты поиска

Содержание HZL-35Z

Отзывы:

Похожие инструкции для HZL-35Z

Бренды по названию

Популярные бренды