JRC JHS-183 Скачать руководство пользователя страница 79

Страница: 79 / 128

5-53

a) Setting change of each item

Each item settings are as follows

The area of setting

1. CH A
2. CH B

・

Item 1 and 2 are setting of the channel numbers.

・

Select

1.CH A

, CH A can be changed. Select

2.CH B

CH B can be changed.

・

Input the channel number with

▲

key or

▼

key and press ENT key. And then the setting is valid.

・

After

1.CH A

setting, the cursor move to

2.CH B

. The setting procedure is same as CH A.

3. TX/RX MODE
Set the CH A/CH B (specified at item 1,2) TRX mode to “TX/RX” or “RX”.
If “TX/RX” is selected, the setting is changed into transmitter-receiver mode. If “RX” is selected, the

setting is changed into receiver mode.

・

Select

3. TX/RX MODE CH A,B

with

▲

key or

▼

key and select the CH A/B mode from the

selection (shown in the table below).

Order Selection

Dialog

TX/RX, TX/RX

CH A and B set transmitter- receiver mode

TX/RX, RX

CH A set transmitter-receiver, CH B set receiver

RX, TX/RX

CH A set receiver, CH B set transmitter-receiver

・

Press ENT key and confirm the setting.

・

It is not acceptable that Sets both CH A and CH B to “RX”.

4. TX POWER
Select

4. TX POWER

, transmission power can be set.

・

Select the transmission power from “HIGH” and “LOW” with

▲

key or

▼

key.

・

If “HIGH” is selected, the power is set 12.5W, if ”LOW” is selected, the power is set 1W.

・

Press ENT key and confirm the setting.

5. ZONE SIZE
Select

5. ZONE SIZE

, zone size width can be input.

・

Press

▲

key or

▼

key to input the zone size width. (Input range; from 1NM to 8NM.)

・

Press ENT key and confirm the input.

6.AREA(NE)
N 15°22.33

’

E 145°59.99

’

7.AREA(SW)
N 14°22.33

’

E 143°59.99

’

5.ZONE SIZE : 5NM

1.CH A      : 1222
2.CH B      : 2222
3.TX/RX MODE: TX/RX,TX/RX
          (CH A ,CH B )
4.TX POWER   : HIGH

•

The set range of coordinates is the distance between

AREA (NE) and AREA (SW) and it is over 20NM and
under 200NM

•

The setting area is within 500NM from own ships position.

Содержание JHS-183

































































































































Результаты поиска

Содержание JHS-183

Отзывы:

Похожие инструкции для JHS-183

Бренды по названию

Популярные бренды

JRC JHS-183, Инструкция по эксплуатации

Результаты поиска

Содержание JHS-183

Отзывы:

Похожие инструкции для JHS-183

Бренды по названию

Популярные бренды