JRC JHS-183 Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 128

background image

8-3

8.3.5 Supported interface sentences

(1)Supported interface sentences

Supported Sentence

Indication Format

Input data

sentences

Positioning system:
Longitude/Latitude
Position Accuracy

GNS, GLL,GGA,RMC

Datum Reference

DTM

Speed Over Ground (SOG)

VBW,VTG,RMC

Course Over Ground (COG)

RMC,VTG

Heading HDT,THS
RAIM indicator

GBS

1

SENSOR1

※)

SENSOR2

※)

SENSOR3

IEC61162-1/2
(NMEA1.5-2.3)

Rate Of Turn (ROT)

ROT

2 SENSOR4

IEC61162-1

The

above

VHW,POS

3

SENSOR4

ITU-R M.823-2

RTCM SC-104 Ver.2.0 Type 1, 2, 7, 9

Binary data

4 SENSOR3

IEC61162-1

Heading

HDT

5 AUX1

※)

,AUX2 IEC61162-2

Input: ABM, ACA, ACK, AIQ, AIR, BBM, EPV, LRI, LRF, POS,
SSD, SPW, VDO, VDM, VSD
Output: ABK, ACA, ACK, ACS, ALR, DSC, DSR, EPV, HBT, LRI,
LRF, LR1,

LR2,

LR3, NAK , SSD, SPW, TXT, TRL,VDO, VDM,

VSD, VER

6 AUX3

IEC61162-2

Output: ABK, ACA, ACK, ACS, ALR, DSC, DSR, EPV, HBT, LRI,
LRF, LR1,

LR2,

LR3, NAK , SSD, SPW, TXT, TRL,VDO, VDM,

VSD, VER

7

Long range

IEC61993-2

Input: LRI,LRF, Output: LRF, LR1,LR2,LR3

8 BIIT

ALARM IEC61993-2

9 Pilot

※)

IEC61162-2

Input: ABM, ACA, ACK, AIQ, AIR, BBM, EPV, LRI, LRF, POS,
SSD, SPW, VDO, VDM, VSD
Output: ABK, ACA, ACK, ACS, ALR, DSC, DSR, EPV, HBT, LRI,
LRF, LR1,

LR2,

LR3, NAK , SSD, SPW, TXT, TRL,VDO, VDM,

VSD, VER

Note) When NQE-5183 connection box is equipped, all sentence are available.

When it is not equipped, 4 terminations which added

※)

mark can be available.

(2)Electrical description interface
Sensor4                                                                                  AUX1-3, Sensor1-3

Load requirements
  Current consumption:

2mA at 2V or less

Maximum input voltage:

±15V or more

Recommended operating current:

2mA or more

Note: IEC61162-2 interfaces comply with the following specifications.
- Output drive capacity: Differential driver output voltage is 2.0V or more (RL=100 ohms), Driver output
current 50mA
- Load on the line of inputs: 100 ohms. 1 IEC61162-2 output can drive 1 IEC61162-2 input.
- Electrical isolation of input circuits: Input circuits are electrically isolated from internal circuit with
opt-isolator.
- The input impedance for the non terminated Sensor1/2/3: between 333k and 357k ohms.

Sensor1; R51, IC504(CDJ-2983) AUX1; R54, IC506(CDJ-2983)
Sensor2; R52, IC505(CDJ-2983) AUX2; R55, IC55
Sensor3; R53, IC53

AUX3; R56, IC56

AUX4;

R57,

IC57

«
...
111
112
113
114
115
...
»

Содержание JHS-183

































































































































Отзывы:

Нет отзывов

Похожие инструкции для JHS-183

Бренд: Nady Systems Страницы: 10

Бренд: Nady Systems Страницы: 19

Бренд: ascon Страницы: 8

Бренд: Immarsat Страницы: 2

Бренд: Fohhn Страницы: 20

Бренд: Leuze electronic Страницы: 58

Бренд: Aiwa Страницы: 68

Бренд: DAEWOO ELECTRONICS Страницы: 34

Бренд: Brähler Systems Страницы: 6

Бренд: Ubiquiti Страницы: 42

Бренд: RCA Страницы: 2

Бренд: Sharp Страницы: 72

Бренд: Listen Technologies Страницы: 4

Бренд: Nagra Страницы: 22

Bewator Entro Series

Бренд: Siemens Страницы: 48

RUGGEDCOM WiN5100

Бренд: Siemens Страницы: 114

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды