JRC JHS-183 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 128

background image

6-8

Symptom of Error

Possible Cause or Cause of Fault

Countermeasures

The illumination does
not light.

The control unit malfunctions.

Replace the CDJ-2983 circuit
board.

The LCD malfunctions.

Replace the LCD unit.

No AIS message is
received.

The transponder is not turned on.

Confirm whether the transponder is
turned on.
(MENU 3.1.1 TRANSPONDER)

The whip antenna is damaged.

Replace the whip antenna.

The following alarm number
appears: 003, 004, or 005.
The synthesizer in the receiving
circuit is unlocked.

Replace the transponder.

Channel setting is not correct.

Set it by operating channels.
(MENU 4.6 CHANNEL/POWER)

No AIS message is
transmitted.

The following alarm number
appears.

Replace the transponder.

001, 052, 53: Power circuit fault
001, 054: PA collector current
abnormal
001, 055: PA temperature abnormal
001, 058: PA protection circuit
operated
001, 060: TX synthesizer unlock
operated
003, 004, 005: RX synthesizer
unlock operated
001, 057: Antenna not connected

Check that the antenna is
connected.
Check the setting of antenna
selection from external and internal.

001, 002: VSWR abnormal

Check that the antenna is
connected.
Check that there are no objects
around the antenna.
Replace the antenna and check for
normal transmission.

MMSI has been set “000000000”

Set the MMSI correctly.

Sensor data (external
GPS, gyro, and
rate-of-turn) cannot be
loaded.

The cable is not connected
properly.

Check the connection.

The polarity of the serial cable is
incorrect.

Check the polarity and connect it.

The interface between the sensor
and connection box is incorrect.

Check the interface before its
connection.

The sentence that the sensor
generates is not supported by the
AIS.

Check the output command and the
version.
(Refer to 8.3.4 Supported Interface
Sentence)

The sentence that the sensor
generates does not match the
sentence setting of the controller.

Check the output sentence and
sensor setting of JHS-183.

The sensor data flag has been set
to “invalid”.

Check if the sensor is working
correctly.

The sensor (GPS, gyro, rate-of-turn
indicator) malfunctions.

Replace the sensor.

The control unit malfunctions.

Replace the CDJ-2983 circuit
board.

«
...
104
105
106
107
108
...
»

Содержание JHS-183

































































































































Отзывы:

Нет отзывов

Похожие инструкции для JHS-183

Бренд: Garmin Страницы: 2

FUSION Apollo MS-WB670

Бренд: Garmin Страницы: 44

Бренд: iHome Страницы: 17

Бренд: JBL Страницы: 24

Бренд: Hama Страницы: 45

Бренд: Emerson Страницы: 16

Бренд: Emerson Страницы: 2

Бренд: Emerson Страницы: 8

Бренд: Emerson Страницы: 28

Бренд: Emerson Страницы: 36

Бренд: Emerson Страницы: 14

Бренд: Emerson Страницы: 31

Бренд: Emerson Страницы: 31

Бренд: Emerson Страницы: 31

Бренд: Emerson Страницы: 48

Бренд: Emerson Страницы: 30

Бренд: Emerson Страницы: 36

Бренд: Emerson Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды