background image

19

ENGLISH

1

.  Airtight steel sheet 

metal

2

.  45° Curves

3

.  Fume exhaust

4

.  External insulated flue

5

.  Insulated T union for 

condensation

6

.  Non-insulated pipe

 

07.2 

FLUE OR FUME EXHAUST SYSTEM

The flue or fume exhaust system is a fundamental element for the proper functioning of the stove and must comply with the following 

general standards:
EN1856-1 

Chimneys. Requirements for metal chimneys - Part 1: System chimney products

EN1856-2  

Chimneys. Requirements for metal chimneys - Part 2: Metal flue liners and connecting flue pipes

UNI 10683  

Heat generators operating with wood or other solid bio fuels - Installation requirements

The diameter of the flue must be sized according to the technical specifications of the appliance and type and place of installation. Each

appliance must have its own chimney flue without any inlets from other appliances.

The exhaust duct of the combustion products generated by the forced draught equipment must respond to the following requirements:

• 

it is necessary to use union joints and pipes with pressure resistant seals, as the union of the flue could be slightly pressurised 

while the appliance running

• 

all changes in direction must be open to inspection to facilitate maintenance

• 

correct draught to maintain depression in the combustion chamber, as per the technical specifications, must be guaranteed

• 

it must be watertight, waterproof and suitably isolated and insulated

• 

must be made of suitable materials that resist normal mechanical stress, heat, the action of the combustion products and acid 

condensations

• 

must be prevailingly vertical structures with deviations from the axis not greater that 45°

• 

must be adequately distanced from combustible or inflammable materials via an air space or suitable insulation

• 

must have an internal section which is preferably circular: square or rectangular sections must have rounded corners with a 

radius of no less than 20 mm

• 

must have an internal section that is constant, free and independent

If the flue is installed externally it must be insulated to prevent the cooling of fumes and formation of condensation. The same is valid for 

the tract from the roof to the chimney cap (Torrino). For the union between the stove and the flue, or if there are deviations or curves, for 

easier, quicker and safer installation, we recommend using double-walled stainless steel pipes. 

The use of pipes in fibre cement for connecting the equipment to the flue is forbidden.

Exhaust pipes must not run through rooms where the installation of combustion equipment is forbidden. The union must be connected 

to the flue in such a way as to ensure they remain airtight when the appliance is operating in pressurised conditions and to avoid the 

formation of condensation and its conveyance to the appliance.

It has to be avoid, as much as possible, the assembly of 

horizontal sections. In any case, the horizontal segment (or its 

horizontal projection) do not have to be longer than two meters 

with minimum slope not less than 5%. The horizontal section 

does not have to be connected directly to the smoke fan output 

but after the first vertical segment (6) 

F

ig

.1.

The  chimney  system  for  the  smoke  exhaust  MUST  be 

dimensioned  and  projected  by  a  Qualified  Engineer. 

He  will  determine  the  proper  smoke  exhaust  system 

taking  into  consideration  the  product  technical  data, 

kind  of  installation,  installation  location  and  mostly  the 

installation  technical  regulation  in  force.  The  Engineer 

will give indications to the installer about the materials to 

use, smoke path section, insulation thickness, corrosion 

resistance  and  all  requirements  needed  for  the  correct 

working of the system product-chimney.
The correct dimension of the air intake for ventilation and 

aeration of the installation location MUST be verified in 

conformity with the technical regulation in force.
Malfunctioning of the product caused by a smoke exhaust 

not  properly  projected  and  dimensioned  WILL  NOT  be 

object of objections to Jolly Mec and interventions at Jolly 

Mec charge.

For appliance that must reach ceiling or wall exhaust outlets 

that are not coaxial with regard to the issue of the fumes from 

the machine, changes in direction must be made using an open 

elbow of 45° (see 

F

ig

.1

).

The use of counter slope elements is forbidden. The flue union 

must have a constant section and allow soot to be collected and 

swept away. Changes in cross-section are only allowed at the 

outlet of the heat generator: the use of adaptors on the coupling 

with the chimney flue is prohibited.

Running other air ducts and installation pipes inside the exhaust 

pipes, even if oversized, is forbidden.

F

ig

.1

2

3

1

4

2

5

6

1,5 m min.

1,5 m min.

Содержание AMBRIA





















































Отзывы: