background image

WARNING: If the information in these instructions is not followed exactly, a fire or explosion may 

result causing property damage, personal injury or loss of life. 

Warning: Improper installation, adjustment, alteration, service or maintenance can cause property 

damage, personal injury or loss of life. Refer to this manual. Installation and service must be performed by 
a qualified installer, service agency or the gas supplier. 

 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 

 

What To Do If You Smell Gas 

Do not try to light any appliance. 

Extinguish any open flame. 

Do not touch any electrical switch. 

Do not use any phone in your building. 

Immediately call your gas supplier from a neighbour's phone. 

If you can not reach your gas supplier, call the fire department. 

For Propane Horizontal installations the venting must be a minimum of one foot vertical off the flue before 
going horizontal. 

Installation Instructions 

Model Number FDV200 - FDV200P 

 Free Standing Direct Vent Gas Stove 

 

 

 

 

Stock #’s: FDV200N, FDV200LP, FDV200PN, FDV200PLP, 

                 

 

 

   FDV200NE, FDV200LPE, FDV200PNE, FDV200PLPE are 

Certified to: ANSI Z21.88-2009, CSA 2.33-2009 

 

 

 

 

 

 

 

 

Printed in Canada 

October 22, 2010

 Part # 200-MAN

 

FOR YOUR SAFETY

 

Read this complete manual before beginning installation. 

These instructions must be kept with the unit for future reference. 

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile 

home, where not prohibited by local codes. 

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for 

use with other gases, unless a certified kit is used.

A Division of R-Co. Inc. 

2340 Logan Avenue 

Winnipeg, Manitoba, Canada R2R 2V3 

Ph: (204) 632-1962 

INSTALLER: Leave this manual with the appliance. 

CONSUMER: Retain this manual for future reference.

Содержание FDV200




































Отзывы: