Jolimark TP830 Series Скачать руководство пользователя

Страница: 9 / 65

TP830 User's Manual

- 4 -

2.3.2 Connecting the Parallel Interface Cable

1. Make sure the computer and the printer are both turned off, plug the parallel cable to the parallel

interface of the printer, Squeeze the wire clips on both sides and make the cable fixed. As shown in
Figure 2-3.

2. Plug the other end of the cable to the computer. Tighten the screws on both sides and make the

cable fixed.

2.3.3 Connecting the USB Interface Cable

1. Plug the USB cable A end (flat shape) into the computer's USB interface.

2. Plug the USB cable B end (square shape) into the printer's USB interface as shown in Figure 2-4.

Figure 2-3 Connecting the parallel interface cable

Figure 2-2 Connecting the cash drawer cable

Caution: Please use the appropriate cash drawer. Manufacturer will not honor warranty

when using unauthorized cash drawer.

Note: Please don't impact the plug after connecting USB interface cable.

Cash drawer interface

Cash drawer cable

Parallel interface

Wire clips

Parallel interface cable

Содержание TP830 Series


































































Результаты поиска

Содержание TP830 Series

Отзывы:

Похожие инструкции для TP830 Series

Бренды по названию

Популярные бренды

Jolimark TP830 Series, Руководство пользователя

Результаты поиска

Содержание TP830 Series

Отзывы:

Похожие инструкции для TP830 Series

Бренды по названию

Популярные бренды