Johnson Controls VMA1930 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 20

Johnson Controls VMA1930 Скачать руководство пользователя страница 14

Table 6: Termination details

Type of field device

Type of Input/

Output

Termination diagrams

24 VAC Binary Output

(Switch Low, Internally

Sourced)

BO

Network Stat with

Phone Jack (Fixed

Address = 199)

SA Bus

Network Stat with

Terminals Addressable SA Bus

Network Stat with

Terminals (Fixed

Address = 199)

SA Bus

Setup and adjustments

Important:

Electrostatic discharge can

damage controller components. Use proper

electrostatic discharge precautions during

installation, setup, and servicing to avoid

damaging the controller.

Setting the controller number

Each controller on a network must have a unique

number on the subnet where it resides in order

to identify it in the Controller Tool for uploading,

downloading, and commissioning.
The controller number is set using three rotary

switches and may be numbered from 000 to 999.

The numbers are ordered from left to right, most

significant bit (MSB) to least significant bit (LSB).
In the following figure the switches are set to

4 2 5, designating this controller as controller

number 425. The controller number must match

the controller number defined in Controller

Configuration Tool (CCT) under

Define Hardware

VMA1930 VAV Controller Installation Guide

14

«
...
12
13
14
15
16
...
»

Содержание VMA1930





















Отзывы:

Нет отзывов