background image

TEC2004-4 and TEC2004-4+PIR Multi-Stage Economizer Wireless Thermostat Controller

Installation Instructions

3

3.

Carefully pull the locking tabs on the right side of 
the mounting base and unlock the PCB. Open the 
PCB to the left as illustrated in Figure 2. 

4.

Pull approximately 152 mm (6 in.) of wire from the 
wall and insert the wire through the hole in the 
mounting base.

5.

Align the mounting base on the wall and use the 
base as a template to mark the two mounting hole 
locations.

6.

Position the mounting base so that the arrow on 
the base points upward to indicate the top of the 
thermostat controller.

Note:

If you need to install the thermostat on an 

electrical junction box, use 2-1/2 x 4 in. 
(63 x 101 mm) square boxes with mud ring covers, 
and avoid smaller 1-1/2 x 4 in. (38 x 101 mm) 
square or 3 x 2 in. (76 x 51 mm) boxes. This 
procedure ensures you have enough space for 
cabling and end-of-line devices, if needed.

Note:

For surface-mount applications, use 

durable mounting hardware, such as Molly bolt 
anchors, that cannot be easily pulled out of the 
mounting surface.

7.

Secure the mounting base to the wall surface using 
two mounting screws as illustrated in Figure 3.

Note:

Be careful not to overtighten the mounting 

screws. 

8.

Swing the PCB back to the right and carefully snap 
it into the locking tabs on the mounting base.

9.

Remove the screw terminal blocks that are 
attached to a disposable adhesive. Figure 4 
illustrates the locations of the screw terminal 
blocks on the thermostat controller. 

Figure 2: Opening the PCB

PCB
Locking
Tabs

F

IG

:p

rn

td

_

c

rc

t_

b

rd

Figure 3: Securing the Mounting Base to the Wall

F

IG

:m

n

tn

g

_

b

s

Figure 4: Removing the Screw Terminal Blocks

F

IG

:t

rm

n

l_

b

lc

k

s

Содержание TEC2004-4

















Отзывы: