Table 1: Installer Configuration Menu (Cont.)
Delays Fan Termination at Cycle’s End
for 60 Seconds
Default: No Delay
(Off)
See the
Setting the Fan Delay (Fan
del)
section.
Sets the Duration for Temporary
Occupancy Time
Default: Three Hours
(3.0 hrs)
See the
Establishing the Temporary
Occupancy Time (TOccTime)
section.
Room Air Sensor Calibration (Offset)
Default:
0.0
°
F (0.0
°
C)
See the
Room Air Sensor Calibration
(Cal RS)
section.
Outdoor Air Sensor Calibration (Offset)
Default:
0.0
°
F (0.0
°
C)
See the
Outdoor Air Sensor
Calibration (Cal OS)
section.
Enable/Disable Second Heating Stage
Default:
Two Stages
See the
Enable/Disable Second
Heating Stage (H Stage)
section.
Enable/Disable Second Cooling Stage
Default:
Two Stages
See the
Enable/Disable Second
Cooling Stage (C Stage)
section.
Disables Heating Operation based on
Outdoor Air Temperature
Default:
120
°
F (49
°
C)
See the
Setting the Heating Lockout
(H lock)
section.
Disables Cooling Operation based on
Outdoor Air Temperature
Default:
-40
°
F (-40
°
C)
See the
Setting the Cooling Lockout
(C lock)
section.
Sets the Number of Events in 24-Hour
Period
Default: Two Events
(2.0)
See the
Selecting the Number of
Events (2/4event)
section.
Sets the Auxiliary Contact as Normally
Open or Normally Closed
Default: Normally Open
(N.O.)
See the
Configuring the Auxiliary
Contact (Aux cont)
section.
Enable/Disable Progressive Recovery
Default:
Off
See the
Enable/Disable Progressive
Recovery (Prog rec)
section.
Configuring the Digital Inputs (DI1 and DI2)
Press the configuration menu access key. The first
prompt is to program Digital Inputs DI1 and DI2.
Fan del
set? Y/N
The digital inputs display an alarm condition when the
input is closed. An alarm message is included on the
scrolling Status Display Menu and when the message
displays, the backlight momentarily lights up.
TOccTime
set? Y/N
Each digital input can be programmed in one of five
conditions.
•
None
– No function is associated with the input.
•
Service
– A Service alarm is displayed.
Cal RS
set? Y/N
•
Filter
– A Filter alarm is displayed.
•
RemNSB
– Remote Night Setback (NSB) timer
clock input. The scheduling is set per the digital
input when this option is selected. The time
continues to be displayed, but the menu related to
scheduling is disabled and no longer accessible.
Cal OS
set? Y/N
−
Open Contact = Occupied setpoints
H Stage
set? Y/N
−
Closed Contacts = Unoccupied setpoints
•
RemOVR
– Remote override contact. This
disables all override menu functions of the
thermostat. The override function is controlled
manually by a remote, momentarily closed
contact. When configured in this mode, the input
operates in a toggle mode. With this function
enabled, it is now possible to toggle between
unoccupied and occupied setpoints for the amount
of time set by the temporary occupancy time
parameter.
When override is enabled through the digital
inputs, an
Override
message appears in the
Status Display Menu.
C Stage
set? Y/N
H lock
set? Y/N
C lock
set? Y/N
To configure the digital inputs while in the Installer
Configuration Menu:
1. Press YES to configure Digital Input 1 or NO to
advance to Digital Input 2.
2/4event
set? Y/N
2. Use the UP/DOWN arrow keys to locate the
desired function for the Digital Input 1. Press YES
to select the desired function.
Aux cont
set? Y/N
3. Press YES to configure Digital Input 2 or NO to
advance to the keypad lockout setup prompt.
4. Use the UP/DOWN arrow keys to locate the
desired function for the Digital Input 2. Press YES
to select the desired function.
Prog rec
set? Y/N
The display now shows the keypad lockout setup
prompt. See the
Enabling Keypad Lockout (Lockout)
section for instructions.
6
T600MSP-2 Programmable Thermostat Installation Instructions
