Johnson Controls (H,Y,C)IDM030B21E Скачать руководство пользователя

Страница: 43 / 50

TC-16004-rev.2

3-11

OPTIONAL PART

Unit Number Setting

The indoor unit numbers are set by the auto-address function. Therefore, an indoor unit number setting

is not required. If the indoor unit number is fixed, set the unit number of all indoor units respectively and

serially. It is recommended that the unit number settings begin with “1”. The setting is set not to overlap

the unit number.

Electrical Wiring Connecting and Setting

Connection between Indoor Units

Perform the connection work as shown below.

Do not run the connected wireless controller cable and the power supply cable (208/230V) in parallel in

the indoor units.

Stabilize the cable with cable bands. Along with the wiring outside the indoor units, the control cables

should not run with the power supply cable (208/230V). Keep a separation of more than 12 inches (30cm)

or run the cable through a grounded metal conduit.

OFF

Unit Number Setting

DSW6 (Tens Digit)

RSW1 (Units Digit)

1 2 3 4 5 6

Set No.1 pin ON.

OFF

1 2 3 4 5 6

DSW6

RSW1

Ex.: Set for No. 16 Unit

Setting

Position

Set by inserting

slotted screwdriver

into the groove.

Set at "6".

Factory setting for DSW6 and RSW1 were set to "0".
Max. 63 units are available for setting.

Indoor Unit No.1

Indoor Unit No.2

Indoor Unit No.3

Connecting Cable
(Accessory)

Wired Controller Cable

Control Cable

(No Polarity)

Power

Supply

Cable

(208/230V)

IR Receiver Kit

For twin, triple or quad combinations,

a communication cable for the wireless

controller is not required.

Use the field-supplied communication cable (AWG18)

for the wired controller cable. The total length

should be within 1640ft (500m). If the total length

is less than 98ft (30m), AWG22 cables can be used.

Power Supply Cable 208/230V

A B 1 2

Содержание (H,Y,C)IDM030B21E



















































Результаты поиска

Содержание (H,Y,C)IDM030B21E

Отзывы:

Похожие инструкции для (H,Y,C)IDM030B21E

Бренды по названию

Популярные бренды

Johnson Controls (H,Y,C)IDM030B21E, Инструкция по эксплуатации

Результаты поиска

Содержание (H,Y,C)IDM030B21E

Отзывы:

Похожие инструкции для (H,Y,C)IDM030B21E

Бренды по названию

Популярные бренды