Johnson Controls (H,Y,C)IDM030B21E Скачать руководство пользователя

Страница: 44 / 50

3-12

TC-16004-rev.2

OPTIONAL PART

3.3.11 Test Run by Wireless Controller (CIR01)

After all installations are completed, a test run should be performed.
(1) Perform the test run according to the Installation Manual of the wireless controller.
(2) The test run from the wireless controller switch takes two hours to complete.

NOTE:

For the wall mount indoor units, if the TIMER indicator (green) is flashing (0.5 second ON/0.5 second

OFF) after two hours, an alarm may occur. Operate the indoor unit ,and check for abnormality.

3.3.12 Alarm Indication

● If a malfunction occurs, such as safety device actuation, during the test run or the normal

operation, “RUN” (red light) flashes (0.5 second ON / 0.5 second OFF).

● The alarm codes are indicated by the number of LED flashes of “DEF” (green light) and “FILTER” (yellow

light).

The first LED light is green. The number of times this LED flashes (0.5 second ON and

OFF) will tell you the “DEF” Alarm Code.

The second LED light is yellow. The number of times this LED flashes (0.5 second ON and

OFF) will tell you the “FILTER” Alarm Code.

Example

● ”RUN” (red light) flashing (1 second ON/1 second OFF) indicates an abnormal transmission (connector

loose, connector disconnection, broken wire, or incorrect wiring, or something similar) between the

indoor unit and the IR receiver kit.

● When the IR receiver kit is connected to multiple indoor units, the alarm code is indicated for each

indoor unit in order.

Alarm Code Table

Further details for alarm codes can be found in the “Installation and Maintenance Manual” for the indoor unit.

"FILTER" (yellow light)

Alarm

3 5

"DEF" (green light)

"DEF" flashes three times (0.5 second ON/ 0.5 second OFF)

"FILTER" flashes five times (0.5 second ON/ 0.5 second OFF)

These signals are repeated until the alarm is reset.

Содержание (H,Y,C)IDM030B21E



















































Результаты поиска

Содержание (H,Y,C)IDM030B21E

Отзывы:

Похожие инструкции для (H,Y,C)IDM030B21E

Бренды по названию

Популярные бренды

Johnson Controls (H,Y,C)IDM030B21E, Инструкция по эксплуатации

Результаты поиска

Содержание (H,Y,C)IDM030B21E

Отзывы:

Похожие инструкции для (H,Y,C)IDM030B21E

Бренды по названию

Популярные бренды