Johnson Controls (H,Y,C)IDM030B21E Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 50

background image

3-2

TC-16004-rev.2

OPTIONAL PART

3.2 Optional Air Filter: KW-PP456E

KW-PP456E is only available to be used in combination with the indoor unit ducted medium static

(EconoFresh) type models.

3.2.1 Procedures

(1) Remove the support piece (three screws) from the indoor unit.
(2) Insert the Optional Air Filter and reattach the support piece.

NOTE:

1. During the installation or removal of the optional air filter if the insulation

material attached on the cabinet is removed, then reapply and repair the

insulation. Otherwise, condensation may occur when cold air enters.

2. It is recommended to follow below indications depending on the installation.

- Attach the Optional Air Filter in a situation where no Suction Duct has been applied. (Figure A)

- If applying a Suction Duct, it is recommended that the Air Filter is applied at the inlet point of the Suction

Duct. (Figure B)

Optional Air Filter

EconoFresh Kit

Indoor Unit

Optional Air Filter Support

Optional Air Filter

inserting direction

3.2.2 Service and Maintenance

Remove the Optional Air Filter from the flange. Vacuum dust. Use a cleaner or wash the air filter with

water or neutral detergent to clean the air filter. Dry the air filter away from direct light.

Dimensions:

Unit: inch (mm)

Name

Illustration

Optional

Air Filter

50-11/16 (1288)

9-9/16

(243)

1/8 (3

)

Optional Air Filter

(Field-Supplied)

Figure A

Air Filter

(Field-Supplied)

Figure B

Suction Duct

A

A

«
...
32
33
34
35
36
...
»

Содержание (H,Y,C)IDM030B21E



















































Отзывы:

Нет отзывов

Похожие инструкции для (H,Y,C)IDM030B21E

Бренд: Zephyr Страницы: 6

Бренд: GD Midea Refrigeration Equipment Страницы: 30

Бренд: Kampmann Страницы: 96

Бренд: Kampmann Страницы: 36

Бренд: Patton Страницы: 4

Бренд: Bard Страницы: 72

Бренд: BASETech Страницы: 12

GJC12AG-E6DRNB9A

Бренд: Gree Страницы: 50

Бренд: Friedrich Страницы: 28

Бренд: York Страницы: 20

Бренд: King Industrial Страницы: 6

Бренд: Rowenta Страницы: 73

V7KI-18WiFiR/U7RS-18

Бренд: INVENTOR Страницы: 144

Бренд: hotspot energy Страницы: 27

Бренд: AirPicnic Страницы: 29

Бренд: Technibel Climatisation Страницы: 21

Бренд: Hunter Страницы: 14

Бренд: Viking Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды