Johnson Controls (H,Y,C)IDM030B21E Скачать руководство пользователя

Страница: 13 / 50

FEATURES

TC-16004-rev.2

1-3

● Standard and All Fresh Process Modes

Two different process modes are selectable:

(1) Standard Process

Standard Process in Cooling Mode

In a situation where the outdoor ambient temperature is lower than 66

F (19

C), the compressor stops and

the indoor temperature is cooled down with an intake of outdoor fresh cold air controlled by the damper.

The minimum guaranteed fresh air intake can be set through the d7 setting (7% or more of the total outlet

air).

• Cooling Economizer

An energy saving control is adopted which uses fresh cold air from the outdoors for cooling the

intermediate seasons. The compressor is not used during this control, which results in outstanding

energy saving.

• Three Different Economizer Cooling Controls
In order to optimize energy savings, EconoFresh can manage three types of control: normal cooling,

outdoor air cooling or fan cooling. Each type is managed according to the outdoor air temperature.

• Comfort Control

When Thermo OFF is requested, EconoFresh compares temperatures in order to offer a comfortable

environment in the room. EconoFresh control compares the set temperature (set in the wired controller)

and the inlet air temperature in the Indoor Unit, and requests Thermo ON under certain conditions, in

order to achieve the requested room temperature as soon as possible.

Standard Process in Heating Mode

Depending on the temperature of indoor air return, the damper remains either opened for a minimum

guaranteed intake of fresh air, or fully closed for 10 minutes. After this time, the damper is opened for a

minimum guaranteed intake of fresh air intake; this opening can be set through the d7 setting (7% or more

of the total outlet air).

(-5)

(4)

(19)

109

(43)

(

100%

Outdoor Temperature

Fresh Ai

Working Area

(-10)

(0)

(10)

(20)

(30)

104

(40)

100

150

200

250

(h/year)

Outdoor Temperature

Example of Temperature Distribution (8:00-21:00)

Compressor not used for Cooling

(

Содержание (H,Y,C)IDM030B21E



















































Результаты поиска

Содержание (H,Y,C)IDM030B21E

Отзывы:

Похожие инструкции для (H,Y,C)IDM030B21E

Бренды по названию

Популярные бренды

Johnson Controls (H,Y,C)IDM030B21E, Инструкция по эксплуатации

Результаты поиска

Содержание (H,Y,C)IDM030B21E

Отзывы:

Похожие инструкции для (H,Y,C)IDM030B21E

Бренды по названию

Популярные бренды