background image

www.johnsonandstarley.co.uk

24

FIGURE 28.

CONDENSATE PUMP REMOVAL

17.9 

CONDENSATE DRAIN PUMP

17.9.1 

Refer to section 16.3. See Figures 24 & 28.

17.9.2 

Disconnect the electrical connections on the electrical panel 
for the Condense Pump and float switch.

17.9.3 

Disconnect the condensate pipes from the “Y” connection 
and from the flue outlet.

NOTE:  

The condensate pump, pipes and tubes will contain water.

17.9.4 

Remove the two screw holding the bracket to the front of the 
cabinet.

17.9.5 

Remove the screw holding the “Y” connection and remove. 

17.9.6 

Unclip the casing and remove the 2 screws holding the pump 
to the bracket. Remove the pump and replace with new.

17.9.7  Check the inlet and outlet pipe ensuring there are no 

restrictions to the flow. 

17.9.6 

Reconnect the condense drain pipe to the condense pump, leaving the flue outlet disconnected, 
pour water into the flue pipe outlet to fill the condensate drain pipe and check for leaks. Reconnect 
the pipe to the flue outlet.

 IMPORTANT:

 The condensing tube from the combustion tray MUST be routed so the tube forms a “S” 

shape, making a “U” trap. Fit the tube behind the Condensate Trap to hold it in place. 
17.9.9    Continue to refit in reverse order. 

17.10  MAIN IGNITION/CONTROL PCB 

(ESYS Red Housing on Gas Valve)

17.10.1 

Refer to section 16.3 and See Figure 29.

17.102 

Unplug the connections from the top of the control and remove the ignition spark detection wires. 

17.10.3  Unscrew the single retaining screw. Remove cover & unplug the multi-pin connections from the 

control. Slide the housing off the gas valve electrical connections.

17.10.4  Replace with the new ignition control PCB and refit in reverser order.

BRACKET 

SCREWS

SCREWS

MAIN SUPPLY

“Y” SCREW

FIGURE 29. MAIN BURNER ASSEMBLY

ESYS PANEL 

SCREW

ELECTRICAL 

CONNECTIONS

BURNER 

ASSEMBLY NUTS

BURNER ARM

COMBUSTION 

CHAMBER

ELECTRODE 

NUTS

BURNER 

ASSEMBLY NUT

FLAME DETECTION ELECTRODE
IGNITION ELECTRODE

GASKET

GAS VALVE

VENTURI

 

GAS COCK

CONNECTION

ESYS

Содержание WARMCAIR C26D













































Отзывы: