background image

 
Installation & Operation manual of Jetmaster UK clean burn range 
 
 

 
 

Page 11 

Revision 10/02/2010 

If needed then the remaining components can be removed. 

 

 

 

Cast Bottom Grate Removal 

The cast bottom grate can be removed by lifting up at the front or side edges. Care should be taken to ensure that 
the V boards each side of the grate do not become damaged. Particularly the thin sections that surround the cast 
bottom grate. 

Internal V Board Removal 

The internal V boards need to be taken out in the following sequence:-  

IMPORTANT

  First  remove  Cast  Bottom  Grate  then  Bottom  V  boards,  then  Rear  V  boards  and  then  the  Side  V 

boards. 

All the V boards are soft to enable them to be stable in high temperatures so care must be taken during handling. 

The position of the V boards must be noted so that they can be replaced back in the same positions. Note also that 
some of the V boards can only be fitted one way around or are handed. 

 

 

 

 

 

 

 

 

 

 

 

Bottom V Board Removal 

First remove the bottom V boards by gently lifting them up at the front edge. 

Care should be taken with the thin 

sections that surround the cast bottom grate so they do not break.

 

Содержание INSET STOVE MKIII 60i























Отзывы: