4L
Four-Wheel Drive Low Range — This range provides low
speed four-wheel drive. It maximizes torque to the front
driveshaft, forcing the front and rear wheels to rotate at
the same speed. This range provides additional traction
and maximum pulling power for loose, slippery road
surfaces only. Do not exceed 25 mph (40 km/h).
This transfer case is designed to be driven in the two-
wheel drive position (2H) or four-wheel drive position
(4H AUTO) for normal street and highway conditions on
dry hard surfaced roads.
For variable driving conditions, the 4H AUTO mode can
be used. In this mode, the front axle is engaged, but the
vehicle's power is sent to the rear wheels. Four-wheel
drive will be automatically engaged when the vehicle
senses a loss of traction. Because the front axle is
engaged, this mode will result in lower fuel economy
than the 2H mode.
In the event that additional traction is required, the
transfer case 4H and 4L positions can be used to lock
the front and rear driveshafts together, forcing the front
and rear wheels to rotate at the same speed. The 4H
and 4L positions are intended for loose, slippery road
surfaces only and not intended for normal driving. Driv-
ing in the 4H and 4L positions on hard-surfaced roads
will cause increased tire wear and damage to the drive-
line components. For further information on shifting
into 4H or 4L
The instrument cluster alerts the driver that the vehicle
is in four-wheel drive, and the front and rear driveshafts
are locked together. The light will illuminate when the
transfer case is shifted into the 4H position.
When operating your vehicle in 4L, the engine speed
will be approximately three times (four times for Rubi-
con models) that of the 2H or 4H positions at a given
road speed. Take care not to overspeed the engine.
Proper operation of four-wheel drive vehicles depends
on tires of equal size, type, and circumference on each
wheel. Any difference will adversely affect shifting and
cause damage to the transfer case.
Because four-wheel drive provides improved traction,
there is a tendency to exceed safe turning and stopping
speeds. Do not go faster than road conditions permit.
Shifting Procedures
2H TO 4H AUTO OR 4H AUTO TO 2H
Shifting between 2H and 4H AUTO can be made with
the vehicle stopped or in motion. The preferred shifting
speed would be 0 to 45 mph (72 km/h). With the
vehicle in motion, the transfer case will engage/
disengage faster if you momentarily release the accel-
erator pedal after completing the shift. Do not acceler-
ate while shifting the transfer case. Apply a constant
force when shifting the transfer case lever.
2H/4H AUTO TO 4H PART TIME OR 4H PART
TIME TO 2H/4H AUTO
Shifting between 2H/4H AUTO to 4H PART TIME can be
made with the vehicle stopped or in motion. The pre-
ferred shifting speed would be 0 to 45 mph (72 km/h).
With the vehicle in motion, the transfer case will
engage/disengage faster if you momentarily release
the accelerator pedal after completing the shift. Do not
accelerate while shifting the transfer case. Apply a con-
stant force when shifting the transfer case lever.
NOTE:
•
Do not attempt to make a shift while only the front or
rear wheels are spinning. The front and rear driveshaft
speeds must be equal for the shift to take place. Shift-
ing while only the front or rear wheels are spinning can
cause damage to the transfer case.
•
Delayed shifts out of four-wheel drive may be experi-
enced due to uneven tire wear, low or uneven tire
pressures, excessive vehicle loading, or cold
temperatures.
•
Shifting effort will increase with speed, this is normal.
During cold weather, you may experience increased
effort in shifting until the transfer case fluid warms up.
This is normal.
4H PART TIME/4H AUTO TO 4L OR 4L TO 4H
PART TIME/4H AUTO
With the vehicle rolling at 1 to 3 mph (2 to 5 km/h), shift an auto-
matic transmission into NEUTRAL (N), or press the clutch pedal on a
manual transmission. While the vehicle is coasting at 1 to 3 mph
(2 to 5 km/h), shift the transfer case lever firmly to the desired posi-
tion. Do not pause with the transfer case in N (Neutral). Once the
shift is completed, place the automatic transmission into DRIVE or
release the clutch pedal on a manual transmission.
NOTE:
Shifting into or out of 4L is possible with the vehicle
completely stopped; however, difficulty may occur due
to the mating teeth not being properly aligned. Several
attempts may be required for clutch teeth alignment
and shift completion to occur. The preferred method is
with the vehicle rolling at 1 to 3 mph (2 to 5 km/h).
Avoid attempting to engage or disengage 4L with the
vehicle moving faster than 1 to 3 mph (2 to 5 km/h).
WARNING!
Failure to engage a transfer case position completely
can cause transfer case damage or loss of power and
vehicle control. You could have a collision. Do not drive
the vehicle unless the transfer case is fully engaged.
STARTING AND OPERATING
157
4
5538906_24_JL_OM_EN_USC_t_E1.pdf 157
5/22/2023 9:02:23 AM
