JDS Uniphase T-BERD 6000A Скачать руководство пользователя страница 28

Страница: 28 / 28

Page 28 of 28

Technical Support

[email protected]

1 866 228-3762

Systems Engineer

[email protected]

321-243-0600

Reset to Defaults

In the

Tools

menu, select

Reset Test to Defaults

. Press

to continue.

Setup

Press the

SETUP

soft key on the top right side of screen.

For Electrical Handoffs: Select the indicated folders and configure your
test as follows.

Folder

Option

Value(s)

Comment

Interface,
Connector

Electrical
Connector

SFP1 or SFP2

Select
ETHERNET 1000BASE-T SFP

Interface,
Physical
Layer

Auto
Negotiation

See Work Order

Set to same value as Ethernet switch port.

For Optical Handoffs: Select the indicated folders and configure your
test as follows.

Folder

Option

Value(s)

Comment

Interface,
Connector

Optical
Connector

SFP1 or SFP2

Select desired optical SFP (1000BASE-
SX, 1000BASE-LX, etc.)

Interface,
Physical
Layer

Auto
Negotiation

See Work Order

Set to same value as Ethernet switch port.

For all handoffs: Select the indicated folders and configure your test as
follows. Leave all other values at default, unless specified in the Work
Order.

Folder

Option

Value(s)

Comment

All Streams

Source IP
Type

Static

Source IP

See Work Order

For Layer 2 handoffs, set to 192.168.1.3

Default
Gateway

See Work Order

For Layer 2 handoffs, set to 192,168.1.1

Subnet Mask

See Work Order

For Layer 2 handoffs, set to
255.255.255.0

1, Ethernet

Encapsulation

See Work Order

None or VLAN

VLAN ID

See Work Order

Options displayed after tapping VLAN
field if Encapsulation = VLAN

1, IP

Destination IP

See Work Order

Options displayed after tapping
Destination IP Address field. For Layer
2 handoffs, set to 192,168.1.2

TCP Host,
Ethernet

Encapsulation

See Work Order

None or VLAN

VLAN ID

See Work Order

Options displayed after tapping VLAN
field if Encapsulation = VLAN

TCP Host,
TCP Host
Settings

TCP Host
Mode

Client

View Results

Press the

RESULTS

button, to display the Results screen.

Test

Inform the A-side technician that you are ready for test.

Содержание T-BERD 6000A





























Результаты поиска

Содержание T-BERD 6000A

Отзывы:

Бренды по названию

Популярные бренды

JDS Uniphase T-BERD 6000A, Руководство по тестированию

Результаты поиска

Содержание T-BERD 6000A

Отзывы:

Бренды по названию

Популярные бренды