JDS Uniphase T-BERD 6000A Скачать руководство пользователя страница 23

Страница: 23 / 28

Page 23 of 28

Technical Support

[email protected]

1 866 228-3762

Systems Engineer

[email protected]

321-243-0600

Reset to Defaults

In the

Tools

menu, select

Reset Test to Defaults

. Press

to continue.

Setup

Press the

SETUP

soft key on the top right side of screen.

For Electrical handoffs: Select the indicated folders and configure your
test as follows.

Folder

Option

Value(s)

Comment

Interface,
Connector

Electrical Connector

SFP1 or
SFP2

Select
ETHERNET 1000BASE-T SFP

Interface,
Physical Layer

Auto Negotiation

See Work
Order

Set to same value as Ethernet
switch port.

Duplex

See Work
Order

Options only displayed if Auto
Negotiate = Off

Speed

For Optical handoffs: Select the indicated folders and configure your
test as follows.

Folder

Option

Value(s)

Comment

Interface,
Connector

Optical Connector

SFP1 or
SFP2

Select desired optical SFP
(1000BASE-SX, 1000BASE-LX,
etc.)

Interface,
Physical Layer

Auto Negotiation

See Work
Order

Set to same value as Ethernet
switch port.

Leave all other values at default, unless specified in the Work Order.

View Results

Press the

RESULTS

button, to display the Results screen.

Start TrueSpeed

Press the

TrueSpeed Test

soft key.

Select Config

Select the

Configs

tab. If this is the first time using the RFC2544 test,

tap

[New]

, enter a name for the new configuration, then tap

[OK]

Otherwise, choose the saved Test Configuration.

Содержание T-BERD 6000A





























Результаты поиска

Содержание T-BERD 6000A

Отзывы:

Бренды по названию

Популярные бренды

JDS Uniphase T-BERD 6000A, Руководство по тестированию

Результаты поиска

Содержание T-BERD 6000A

Отзывы:

Бренды по названию

Популярные бренды