JDS Uniphase T-BERD 6000A Скачать руководство пользователя страница 19

Страница: 19 / 28

Page 19 of 28

Technical Support

[email protected]

1 866 228-3762

Systems Engineer

[email protected]

321-243-0600

Configure Test

Press the

Configure

Navigation key to configure test setting. Using the

Right Arrow

key or

Settings

soft key, scroll through Settings menus

and configure your test as follows. Leave all other values at default,
unless specified in the Work Order.

For Layer 2 Testing:

For Layer 3 IP Testing:

View Results

Press the

Home

key to display Summary Results.

Turn Laser On

For optical testing, press the

Action

soft key and select

Laser On

10.

Restart

Press the

Restart

soft key to reset test results.

11.

Check LED Results Press the

Right Arrow

key until

LED Results

are displayed. A

Green

Signal Present LED indicates that the HST-3000 is receiving an optical
signal from the near end Ethernet Switch.

Green

Sync Acquired

and

Link Active

LEDs indicate that the HST-3000 has successfully

connected to the near end Ethernet switch and the Ethernet link is active.

Menu

Option

Value

Comment

Test Mode

Test

Layer 2 Traffic

RFC 2544 Mode

Disable

Link Init

Auto Negotiation

See Work Order

Set to same values as
Ethernet switch port.

Speed

See Work Order

Duplex

Full

Menu

Option

Value

Comment

Test Mode

Test

Layer 3 IP Traffic

RFC 2544 Mode

Disable

Link Init

Auto Negotiation

See Work Order

Set to same values as
Ethernet switch port.

Speed

See Work Order

Duplex

Full

IP Init

ARP Mode

Disable

Source Type

Static IP

Source IP

See Work Order

Subnet Mask

See Work Order

Default Gateway

See Work Order

Содержание T-BERD 6000A





























Результаты поиска

Содержание T-BERD 6000A

Отзывы:

Бренды по названию

Популярные бренды

JDS Uniphase T-BERD 6000A, Руководство по тестированию

Результаты поиска

Содержание T-BERD 6000A

Отзывы:

Бренды по названию

Популярные бренды