JBT Fresh'n Squeeze Series Скачать руководство пользователя

Страница: 20 / 96

FNS-0014-060-EN June 2019 Rev A

Safety Circuit Fault

When this message occurs it indicates there is a problem with one of the safety sensors. The

juicer will not run until the problem has been fixed.
It is possible one of the cables is not connected. Turn off the juicer and verify that all cables are

connected properly.
If the cables are connected, then it is possible a safety sensor has failed. Follow the procedure

for checking safety circuits in the “Electrical Drawings and Procedures” section of this manual to

determine which sensor is faulty.
This screen can be disabled. There is a hidden button in the bottom right corner (A), this pulls

up the password which is the same as for the service screen. Once on the service screen, go to

the second service screen and turn off the safety check.

NOTE:

This will not fix a problem, if a cable is unplugged or safety has failed, the juicer will

still not run.

Содержание Fresh'n Squeeze Series

































































































Результаты поиска

Содержание Fresh'n Squeeze Series

Отзывы:

Похожие инструкции для Fresh'n Squeeze Series

Бренды по названию

Популярные бренды

JBT Fresh'n Squeeze Series, Руководство по обслуживанию

Результаты поиска

Содержание Fresh'n Squeeze Series

Отзывы:

Похожие инструкции для Fresh'n Squeeze Series

Бренды по названию

Популярные бренды