JBT Fresh'n Squeeze Series Скачать руководство пользователя

Страница: 34 / 96

FNS-0014-060-EN June 2019 Rev A

Rebuilding (Continued)

4. Remove linear shafts.

With a 3/16" Allen wrench, loosen set screws at top and bottom of all three shafts.

Back screws out at least 1/4" to clear flats on shafts. If shafts are stuck, use bearing removal

puller with 3/8"-16 x 2" hex head cap screw to break free shafts.
(Note: Lower Shaft will be removed downward through the waste bin area)

Refer to Figure 15.

5. Lift out upper and lower drive arms with linkages still attached.

Refer to Figure 16.

6. Disassemble linkages arms from drive and crank arms.

Note location and numbers of washers and spacers.

7. Using a similar process to step 4 Remove sprockets from shafts and then shafts from

frame.

Pull or pry on large diameter upper drive sprocket, repeat for lower drive sprocket.

Refer to Figure 17.

Figure 15. Removal of Linear Shafts

Содержание Fresh'n Squeeze Series

































































































Результаты поиска

Содержание Fresh'n Squeeze Series

Отзывы:

Похожие инструкции для Fresh'n Squeeze Series

Бренды по названию

Популярные бренды

JBT Fresh'n Squeeze Series, Руководство по обслуживанию

Результаты поиска

Содержание Fresh'n Squeeze Series

Отзывы:

Похожие инструкции для Fresh'n Squeeze Series

Бренды по названию

Популярные бренды